VOLVO
BCM-0121 - Yaw rate sensor. Signal outside its permitted range
System
Bremsestyring (BCM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
10 modellerC30 (2007–2013), C30 Electric (2011–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Vis modeller per årsmodell og motor (21)
- Volvo C30 (2007–2013)2007–2011
- Volvo C30 (2007–2013)2012Alle motorer unntatt: D4162T, D5204T, D5204T5
- Volvo C30 (2007–2013)2013Kun motor: B4204S3, B4204S4, B5254T7
- Volvo C30 Electric (2011–2013)2011–2013
- Volvo C70 (2006–2013)2006–2011
- Volvo C70 (2006–2013)2012–2013Kun motor: B5254T7
- Volvo S40 (2004–2013)2004–2010
- Volvo S40 (2004–2013)2011–2012Alle motorer unntatt: D4162T, D5204T, D5204T5
- Volvo S60 (2001–2009)2002–2009
- Volvo S80 (1999–2006)2002–2006
- Volvo V50 (2004–2013)2004–2010
- Volvo V50 (2004–2013)2011–2012Alle motorer unntatt: D4162T, D5204T, D5204T5
- Volvo V70 (2000–2008)2002–2008
- Volvo V70 XC / XC70 (2001–2007)2002–2007
- Volvo XC90 (2003–)2003–2004, 2015
- Volvo XC90 (2003–)2005–2006Alle motorer unntatt: B8444S
- Volvo XC90 (2003–)2007Kun motor: B5254T2, D5244T4
- Volvo XC90 (2003–)2008–2010Alle motorer unntatt: B6324S, B8444S
- Volvo XC90 (2003–)2011Alle motorer unntatt: B6324S5, B8444S
- Volvo XC90 (2003–)2012Alle motorer unntatt: B6324S5
- Volvo XC90 (2003–)2013–2014Kun motor: B5254T9
Hva betyr feilkoden?
The AYC sensor contains the yaw rate sensor, the lateral acceleration sensor, the accelerometer and the lean sensor, and is connected to the brake control module on its own CAN wire. If the signal from the yaw rate sensor is implausible, the code is set. The fault may come from interference, low supply voltage or an internal fault in the sensor.
Mulige årsaker
- Interference or noise on the wires that has disturbed the AYC sensor's calculations
- Supply voltage to the AYC sensor too low
- Incorrect wheel alignment
- Internal fault in the AYC sensor
- Interference on the wires that has disturbed the stability sensor's (BSC) calculations
Hva du kan gjøre
- 1Check the connectors at the brake control module and the AYC sensor for contact resistance and oxidation
- 2Make sure no source of interference, for example a mobile phone or radio receiver, sits too close to the AYC sensor
- 3If the code status is intermittent, poor contact or an interference source has probably been the cause; if the fault remains, have a workshop check the sensor
- 4The brake system is safety critical: do not replace the brake control module for this code, and drive carefully until the fault is fixed
Symptomer du kan merke5
- General yellow warning lamp on
- Anti-spin does not work
- Stability function does not work
- Anti-skid does not work
- Traction control does not work
Hva feilen kan påvirke2
- Traction control (TC), stability control (SC) and active yaw control (AYC) are disabled
- Roll stability control (RSC) is disabled on cars that have it
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.