VOLVO
BCM-0148 - Communication between control modules. Faulty configuration ID
System
Bremsestyring (BCM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
10 modellerC30 (2007–2013), C30 Electric (2011–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Vis modeller per årsmodell og motor (21)
- Volvo C30 (2007–2013)2007–2011
- Volvo C30 (2007–2013)2012Alle motorer unntatt: D4162T, D5204T, D5204T5
- Volvo C30 (2007–2013)2013Kun motor: B4204S3, B4204S4, B5254T7
- Volvo C30 Electric (2011–2013)2011–2013
- Volvo C70 (2006–2013)2006–2011
- Volvo C70 (2006–2013)2012–2013Kun motor: B5254T7
- Volvo S40 (2004–2013)2004–2010
- Volvo S40 (2004–2013)2011–2012Alle motorer unntatt: D4162T, D5204T, D5204T5
- Volvo S60 (2001–2009)2002–2009
- Volvo S80 (1999–2006)2002–2006
- Volvo V50 (2004–2013)2004–2010
- Volvo V50 (2004–2013)2011–2012Alle motorer unntatt: D4162T, D5204T, D5204T5
- Volvo V70 (2000–2008)2002–2008
- Volvo V70 XC / XC70 (2001–2007)2002–2007
- Volvo XC90 (2003–)2003–2004, 2015
- Volvo XC90 (2003–)2005–2006Alle motorer unntatt: B8444S
- Volvo XC90 (2003–)2007Kun motor: B5254T2, D5244T4
- Volvo XC90 (2003–)2008–2010Alle motorer unntatt: B6324S, B8444S
- Volvo XC90 (2003–)2011Alle motorer unntatt: B6324S5, B8444S
- Volvo XC90 (2003–)2012Alle motorer unntatt: B6324S5
- Volvo XC90 (2003–)2013–2014Kun motor: B5254T9
Hva betyr feilkoden?
The steering angle sensor module (SAS) and the steering wheel module (SWM) send data to the brake control module in small packets, and each packet has an identifier number. The code is set if the brake control module receives an identifier that does not match the one it expects. The code may be stored when the brake control module is programmed.
Mulige årsaker
- Interference or intermittent breaks on the CAN network
- Internal fault in the steering angle sensor module (SAS)
- Fault inside the steering wheel module (SWM)
Hva du kan gjøre
- 1Clear the code if it was set during programming of the brake control module, and check that it does not return
- 2Read the codes in the steering angle sensor module and the steering wheel module and fault-find according to them
- 3Check the CAN communication with diagnostic equipment, and replace the steering angle sensor module if it is faulty
- 4The brake system is safety critical: do not replace the brake control module for this code, and drive carefully until the fault is fixed
Symptomer du kan merke5
- Anti-spin warning lamp on
- General yellow warning lamp on
- Anti-spin does not work
- Stability function does not work
- Anti-skid does not work
Hva feilen kan påvirke1
- Traction control (TC), stability control (SC) and active yaw control (AYC) are disabled
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.