VOLVO
BCM-U030000 - Internal Control Module Software Incompatibility. General Failure Information. No sub type information
System
Bremsestyring (BCM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
12 modellerC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V50 (2004–2013), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Vis modeller per årsmodell og motor (19)
- Volvo C30 (2007–2013)2011–2013Kun motor: D4162T, D5204T, D5204T5
- Volvo C70 (2006–2013)2011Kun motor: D5204T, D5204T5
- Volvo C70 (2006–2013)2012–2013Alle motorer unntatt: B5254T7
- Volvo S40 (2004–2013)2011–2012Kun motor: D4162T, D5204T, D5204T5
- Volvo S60 (2011–)2011–2015
- Volvo S80 (2007–)2007–2015
- Volvo V50 (2004–2013)2011–2012Kun motor: D4162T, D5204T, D5204T5
- Volvo V60 (2011–)2011–2012
- Volvo V60 (2011–)2013–2014Alle motorer unntatt: D82PHEV
- Volvo V60 (2011–)2015Alle motorer unntatt: D82PHEV, D87PHEV
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008–2015
- Volvo XC60 (2009–)2009–2015
- Volvo XC70 (2008–)2008–2015
- Volvo XC90 (2003–)2005–2006Kun motor: B8444S
- Volvo XC90 (2003–)2007–2010Kun motor: B6324S, B8444S
- Volvo XC90 (2003–)2011Kun motor: B6324S5, B8444S
- Volvo XC90 (2003–)2012Kun motor: B6324S5
- Volvo XC90 (2003–)2013–2014Alle motorer unntatt: B5254T9
Hva betyr feilkoden?
The BCM checks its own configuration ID against the one sent by the CEM over the CAN network. If the IDs do not match, or if communication with the CEM has been interrupted, the code is set. The module then responds to diagnostic commands, but normal communication does not work.
Mulige årsaker
- Incorrect configuration ID in the brake control module, for example a used module with software or hardware not intended for the car
- Break in the CAN wires between the brake control module and the central electronic module
Hva du kan gjøre
- 1Read codes in the central electronic module; if it shows a loss of power supply to a module, troubleshoot that module first
- 2Check that the correct brake control module is fitted for the car, especially if a used module has been installed
- 3Check the CAN wiring between the brake control module and the central electronic module for breaks and contact resistance
- 4Have a workshop program the brake control module with the correct software and check that the code is not set again
- 5The brake system is safety-critical, so have a workshop carry out all work on the module and its software
Symptomer du kan merke5
- ABS warning lamp lit
- Brake circuit warning lamp lit
- Stability, traction and anti-skid functions do not work
- Adaptive cruise control and collision warning with brake support do not work
- Message in the text display
Hva feilen kan påvirke3
- The module switches itself off and responds only to diagnostic commands
- Locking-free brakes, stability control and traction control are disabled
- Dynamic stability control (AYC) is disabled
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.