VOLVO
DEM-E003 - Configuration fault. Faulty configuration
System
Firehjulsdrift (DEM)
Volvo-modeller feilkoden gjelder for
Feilkoden har ulik betydning avhengig av modell, årsmodell eller motor. Velg betydningen som gjelder din bil.
Gjelder følgende modeller:
7 modellerS40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Vis modeller per årsmodell og motor (14)
- Volvo S40 (2004–2013)2005–2010Kun girkasse: AW50/51 AWD, M66 AWD
- Volvo S60 (2001–2009)2003–2005Alle girkasser unntatt: AW55-50/51SN
- Volvo S60 (2001–2009)2006–2008Alle girkasser unntatt: AW55-50/51SN, TF-80SC
- Volvo S60 (2001–2009)2009Kun girkasse: AW50/51 AWD, M58
- Volvo S80 (1999–2006)2003–2006Kun girkasse: AW50/51 AWD
- Volvo V50 (2004–2013)2005–2010Kun girkasse: AW50/51 AWD, M66 AWD
- Volvo V70 (2000–2008)2003–2005Alle girkasser unntatt: AW55-50/51SN
- Volvo V70 (2000–2008)2006–2007Alle girkasser unntatt: AW55-50/51SN, TF-80SC
- Volvo V70 XC / XC70 (2001–2007)2003–2007
- Volvo XC90 (2003–)2003–2004, 2006Alle girkasser unntatt: AW55-50/51SN
- Volvo XC90 (2003–)2005Alle girkasser unntatt: AW55-50/51SN, TF-80SC AWD
- Volvo XC90 (2003–)2007Alle girkasser unntatt: AW55-50/51SN, TF-80SC
- Volvo XC90 (2003–)2008Alle girkasser unntatt: TF-80SC
- Volvo XC90 (2003–)2009Kun girkasse: AW50/51 AWD
Hva betyr feilkoden?
The module checks its configuration ID against the signal configuration that the CEM transmits. The code is also stored when communication with the CEM is broken. If the module is not intended for this particular car it may be the cause, and then the correct software must be loaded. Because the module does not respond during a permanent break, the code can only be read out when the fault is intermittent.
Mulige årsaker
- Incorrect CAN configuration ID, for example from a used module intended for another vehicle
- Break in the CAN wires between the module and the CEM
Hva du kan gjøre
- 1Read the codes in all control modules and note whether codes for lost communication are stored in the CEM; troubleshoot from those first
- 2If a control module has been replaced, tell the workshop that it may need the correct software for this particular car
- 3Check that the CAN wires between the modules are secure, not chafed, and that the connectors are clean
- 4Use a multimeter to check that the CAN wires have no contact with ground or battery voltage when they are unplugged
- 5If the fault remains, have a workshop load new software into the control module and erase the code afterwards
Symptomer du kan merke4
- The four-wheel drive does not work
- Message in the display, depending on model
- The traction control warning lamp lights
- The general warning lamp lights
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.