VOLVO
ECM-131D - Intake air temperature (IAT) sensor. Signal too low
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
9 modellerC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Vis modeller per årsmodell og motor (23)
- Volvo C30 (2007–2013)2007Kun motor: B5254T3
- Volvo C30 (2007–2013)2008–2013Kun motor: B5254T7
- Volvo C70 (2006–2013)2006–2007Kun motor: B5254T3
- Volvo C70 (2006–2013)2008–2013Kun motor: B5254T7
- Volvo S40 (2004–2013)2005–2007Kun motor: B5254T3
- Volvo S40 (2004–2013)2008Kun motor: B5254T3, B5254T7
- Volvo S40 (2004–2013)2009–2012Kun motor: B5254T7
- Volvo S60 (2001–2009)2005–2006Kun motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2007Kun motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2008–2009Kun motor: B5204T5, B5244T5, B5254T2
- Volvo S80 (1999–2006)2005–2006Kun motor: B5204T5, B5244T4, B5254T2, B6294S2, B6294T
- Volvo V50 (2004–2013)2005–2007Kun motor: B5254T3
- Volvo V50 (2004–2013)2008–2012Kun motor: B5254T7
- Volvo V70 (2000–2008)2005Kun motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2006–2007Kun motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2008Kun motor: B5254T2
- Volvo V70 XC / XC70 (2001–2007)2005Alle motorer unntatt: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Kun motor: B5244T4, B5254T2
- Volvo V70 XC / XC70 (2001–2007)2007Kun motor: B5254T2
- Volvo XC90 (2003–)2005–2006Kun motor: B5254T2, B6294T
- Volvo XC90 (2003–)2007–2012Kun motor: B5254T2
- Volvo XC90 (2003–)2013–2014Kun motor: B5254T9
- Volvo XC90 (2003–)2015
Hva betyr feilkoden?
The engine control module (ECM) monitors the signal from the intake air temperature sensor. The fault is set when the signal corresponds to a temperature below a set value, meaning the signal is too low. The cause can be poor contact, a break or a short in the signal wire, or a damaged sensor.
Mulige årsaker
- Contact resistance in the connections
- Open circuit in the signal wire
- Signal wire shorted to voltage
- Damaged intake air temperature sensor
- Signal wire shorted to ground
Hva du kan gjøre
- 1Read the fault code, clear it and test drive to see whether it returns
- 2Check the intake air temperature sensor connector for contact resistance and oxidation; where the sensor is built into the boost pressure sensor, check that connector
- 3If you have a diagnostic tool: if the intake air temperature in live data becomes reasonable after cleaning the connector, poor contact was likely the cause
- 4Check the sensor wiring for breaks and chafing
- 5If the signal wire has been shorted to voltage, the sensor may have been damaged; check the wiring before replacing the sensor
- 6If no fault is found and the fault remains: have a workshop replace or check the sensor
Symptomer du kan merke2
- Engine warning lamp comes on
- Reduced performance
Hva feilen kan påvirke3
- The engine control uses a predefined intake air temperature value
- Catalyst warm-up is switched off
- The idle control diagnosis is switched off
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.