VOLVO
ECM-2450 - Front heated oxygen sensor (HO2S), bank 1. Faulty signal
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
9 modellerC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Vis modeller per årsmodell og motor (23)
- Volvo C30 (2007–2013)2007Kun motor: B5254T3
- Volvo C30 (2007–2013)2008–2013Kun motor: B5254T7
- Volvo C70 (2006–2013)2006–2007Kun motor: B5254T3
- Volvo C70 (2006–2013)2008–2013Kun motor: B5254T7
- Volvo S40 (2004–2013)2005–2007Kun motor: B5254T3
- Volvo S40 (2004–2013)2008Kun motor: B5254T3, B5254T7
- Volvo S40 (2004–2013)2009–2012Kun motor: B5254T7
- Volvo S60 (2001–2009)2005–2006Kun motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2007Kun motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2008–2009Kun motor: B5204T5, B5244T5, B5254T2
- Volvo S80 (1999–2006)2005–2006Kun motor: B5204T5, B5244T4, B5254T2, B6294S2, B6294T
- Volvo V50 (2004–2013)2005–2007Kun motor: B5254T3
- Volvo V50 (2004–2013)2008–2012Kun motor: B5254T7
- Volvo V70 (2000–2008)2005Kun motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2006–2007Kun motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2008Kun motor: B5254T2
- Volvo V70 XC / XC70 (2001–2007)2005Alle motorer unntatt: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Kun motor: B5244T4, B5254T2
- Volvo V70 XC / XC70 (2001–2007)2007Kun motor: B5254T2
- Volvo XC90 (2003–)2005–2006Kun motor: B5254T2, B6294T
- Volvo XC90 (2003–)2007–2012Kun motor: B5254T2
- Volvo XC90 (2003–)2013–2014Kun motor: B5254T9
- Volvo XC90 (2003–)2015
Hva betyr feilkoden?
The ECM has detected an internal fault in its control of the oxygen sensors. The fault is therefore in the control module, not in the sensors or the wiring. It may be temporary and already gone, or it may remain and require a new control module.
Mulige årsaker
- Damaged engine control module (ECM)
- Temporary interference when the engine control module starts
Hva du kan gjøre
- 1Read and note the code, clear it and start the car several times to see whether it returns
- 2Check that the battery is in good condition, since low voltage at start-up can cause temporary faults
- 3Make sure the connectors to the engine control module are fully seated and clean
- 4If the fault returns, have a workshop with diagnostic equipment decide whether the engine control module needs replacing
Symptomer du kan merke1
- The malfunction indicator lamp (MIL) is lit
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.