VOLVO
ECM-273D - Engine coolant temperature (ECT) sensor. Signal too low
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
9 modellerC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Vis modeller per årsmodell og motor (23)
- Volvo C30 (2007–2013)2007Kun motor: B5254T3
- Volvo C30 (2007–2013)2008–2013Kun motor: B5254T7
- Volvo C70 (2006–2013)2006–2007Kun motor: B5254T3
- Volvo C70 (2006–2013)2008–2013Kun motor: B5254T7
- Volvo S40 (2004–2013)2005–2007Kun motor: B5254T3
- Volvo S40 (2004–2013)2008Kun motor: B5254T3, B5254T7
- Volvo S40 (2004–2013)2009–2012Kun motor: B5254T7
- Volvo S60 (2001–2009)2005–2006Kun motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2007Kun motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2008–2009Kun motor: B5204T5, B5244T5, B5254T2
- Volvo S80 (1999–2006)2005–2006Kun motor: B5204T5, B5244T4, B5254T2, B6294S2, B6294T
- Volvo V50 (2004–2013)2005–2007Kun motor: B5254T3
- Volvo V50 (2004–2013)2008–2012Kun motor: B5254T7
- Volvo V70 (2000–2008)2005Kun motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2006–2007Kun motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2008Kun motor: B5254T2
- Volvo V70 XC / XC70 (2001–2007)2005Alle motorer unntatt: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Kun motor: B5244T4, B5254T2
- Volvo V70 XC / XC70 (2001–2007)2007Kun motor: B5254T2
- Volvo XC90 (2003–)2005–2006Kun motor: B5254T2, B6294T
- Volvo XC90 (2003–)2007–2012Kun motor: B5254T2
- Volvo XC90 (2003–)2013–2014Kun motor: B5254T9
- Volvo XC90 (2003–)2015
Hva betyr feilkoden?
The ECM reads the coolant temperature sensor signal. If it shows a temperature below a certain value, the ECM treats it as a fault and the code is set. The fault may lie in the connectors, the wires to the sensor, or the sensor itself.
Mulige årsaker
- Contact resistance and oxidation in the connections
- Open circuit in the signal wire
- Open circuit in the signal ground wire
- Damaged engine coolant temperature sensor
Hva du kan gjøre
- 1Disconnect the connector to the electric cooling fan before troubleshooting, so the fan does not start by itself
- 2Check the connector at the temperature sensor for contact resistance and oxidation
- 3Start the engine and read the temperature. If it is now plausible, the connector has most likely been making poor contact
- 4Use a multimeter to check the signal and ground wires to the sensor for open circuits
- 5Have a workshop replace the coolant temperature sensor if the wires are intact and the fault remains
Symptomer du kan merke2
- Malfunction indicator lamp (MIL) on
- The engine is hard to start
Hva feilen kan påvirke3
- Boost pressure follows a basic value
- The engine temperature is worked out by a model instead of being measured
- The electric cooling fan runs at a preset speed
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.