VOLVO
ECM-2850 - Heated oxygen sensor (HO2S). Signal too low
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Feilkoden har ulik betydning avhengig av modell, årsmodell eller motor. Velg betydningen som gjelder din bil.
Gjelder følgende modeller:
8 modellerC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Vis modeller per årsmodell og motor (20)
- Volvo C30 (2007–2013)2007Kun motor: D5244T8, D5244T9
- Volvo C30 (2007–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo C70 (2006–2013)2007Kun motor: D5244T8, D5244T9
- Volvo C70 (2006–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo S40 (2004–2013)2006Kun motor: D5244T8
- Volvo S40 (2004–2013)2007Kun motor: D5244T8, D5244T9
- Volvo S40 (2004–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo S60 (2001–2009)2006Kun motor: D5244T4, D5244T5, D5244T6, D5244T7
- Volvo S60 (2001–2009)2007–2009Kun motor: D5244T4, D5244T5, D5244T7
- Volvo V50 (2004–2013)2006Kun motor: D5244T8
- Volvo V50 (2004–2013)2007Kun motor: D5244T8, D5244T9
- Volvo V50 (2004–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo V70 (2000–2008)2006Kun motor: D5244T4, D5244T5, D5244T6, D5244T7
- Volvo V70 (2000–2008)2007Kun motor: D5244T4, D5244T5, D5244T7
- Volvo V70 (2000–2008)2008Kun motor: D5244T5, D5244T7
- Volvo V70 XC / XC70 (2001–2007)2006–2007Kun motor: D5244T4
- Volvo XC90 (2003–)2006–2007Kun motor: D5244T4
- Volvo XC90 (2003–)2008–2010Kun motor: D5244T4, D5244T5
- Volvo XC90 (2003–)2011Kun motor: D5244T18, D5244T4, D5244T5
- Volvo XC90 (2003–)2012Alle motorer unntatt: B5254T2, B6324S5
Hva betyr feilkoden?
The engine control module uses the signal from the oxygen sensor to judge the fuel and air mixture. The code is stored when the control module finds that the sensor signal is wrong, in this case too low. The cause may be an open supply or a short circuit in the signal cable.
Mulige årsaker
- Open circuit in the supply voltage to the sensor
- Damaged oxygen sensor
- Signal cable shorted to ground
- Signal cable shorted to supply voltage
Hva du kan gjøre
- 1Switch off the ignition and check the oxygen sensor connector: look for play, oxidation and damage
- 2Check the insulation of the signal cable for chafing and pinching, especially where it runs close to hot parts
- 3With the ignition on, use a multimeter to check that the supply voltage to the sensor is not interrupted
- 4If you have a diagnostic tool: check whether the oxygen sensor value in live data changes while driving. A value that stays still or looks wrong suggests the signal is not correct
- 5If the wiring is in order but the fault remains, have a workshop check the sensor with diagnostic equipment
Symptomer du kan merke1
- Message in the information display
Hva feilen kan påvirke1
- The last measured value from the sensor is used
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.