VOLVO
ECM-2860 - Heated oxygen sensor (HO2S). Signal too low
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Feilkoden har ulik betydning avhengig av modell, årsmodell eller motor. Velg betydningen som gjelder din bil.
Gjelder følgende modeller:
8 modellerC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Vis modeller per årsmodell og motor (20)
- Volvo C30 (2007–2013)2007Kun motor: D5244T8, D5244T9
- Volvo C30 (2007–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo C70 (2006–2013)2007Kun motor: D5244T8, D5244T9
- Volvo C70 (2006–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo S40 (2004–2013)2006Kun motor: D5244T8
- Volvo S40 (2004–2013)2007Kun motor: D5244T8, D5244T9
- Volvo S40 (2004–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo S60 (2001–2009)2006Kun motor: D5244T4, D5244T5, D5244T6, D5244T7
- Volvo S60 (2001–2009)2007–2009Kun motor: D5244T4, D5244T5, D5244T7
- Volvo V50 (2004–2013)2006Kun motor: D5244T8
- Volvo V50 (2004–2013)2007Kun motor: D5244T8, D5244T9
- Volvo V50 (2004–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo V70 (2000–2008)2006Kun motor: D5244T4, D5244T5, D5244T6, D5244T7
- Volvo V70 (2000–2008)2007Kun motor: D5244T4, D5244T5, D5244T7
- Volvo V70 (2000–2008)2008Kun motor: D5244T5, D5244T7
- Volvo V70 XC / XC70 (2001–2007)2006–2007Kun motor: D5244T4
- Volvo XC90 (2003–)2006–2007Kun motor: D5244T4
- Volvo XC90 (2003–)2008–2010Kun motor: D5244T4, D5244T5
- Volvo XC90 (2003–)2011Kun motor: D5244T18, D5244T4, D5244T5
- Volvo XC90 (2003–)2012Alle motorer unntatt: B5254T2, B6324S5
Hva betyr feilkoden?
The engine control module gets its fuel and air mixture reading from the oxygen sensor. This code is stored when that signal is found to be wrong; here it is too low. The cause may be a signal cable shorted to ground or a damaged sensor.
Mulige årsaker
- Signal cable shorted to ground
- Damaged oxygen sensor
Hva du kan gjøre
- 1Switch off the ignition and check the oxygen sensor connector: it should be secure and clean
- 2With the car switched off, use a multimeter to check that the signal cable is isolated from ground
- 3With a diagnostic tool, check the live data: a value that stays too low all the time points to the sensor or wiring
- 4If the signal cable is in order but the fault remains, have a workshop check the sensor with diagnostic equipment
Symptomer du kan merke1
- Message in the information display
Hva feilen kan påvirke1
- The control module uses the last value it measured from the sensor
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.