VOLVO
ECM-2890 - Lambda control. Faulty signal
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
8 modellerC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Vis modeller per årsmodell og motor (20)
- Volvo C30 (2007–2013)2007Kun motor: D5244T8, D5244T9
- Volvo C30 (2007–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo C70 (2006–2013)2007Kun motor: D5244T8, D5244T9
- Volvo C70 (2006–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo S40 (2004–2013)2006Kun motor: D5244T8
- Volvo S40 (2004–2013)2007Kun motor: D5244T8, D5244T9
- Volvo S40 (2004–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo S60 (2001–2009)2006Kun motor: D5244T4, D5244T5, D5244T6, D5244T7
- Volvo S60 (2001–2009)2007–2009Kun motor: D5244T4, D5244T5, D5244T7
- Volvo V50 (2004–2013)2006Kun motor: D5244T8
- Volvo V50 (2004–2013)2007Kun motor: D5244T8, D5244T9
- Volvo V50 (2004–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo V70 (2000–2008)2006Kun motor: D5244T4, D5244T5, D5244T6, D5244T7
- Volvo V70 (2000–2008)2007Kun motor: D5244T4, D5244T5, D5244T7
- Volvo V70 (2000–2008)2008Kun motor: D5244T5, D5244T7
- Volvo V70 XC / XC70 (2001–2007)2006–2007Kun motor: D5244T4
- Volvo XC90 (2003–)2006–2007Kun motor: D5244T4
- Volvo XC90 (2003–)2008–2010Kun motor: D5244T4, D5244T5
- Volvo XC90 (2003–)2011Kun motor: D5244T18, D5244T4, D5244T5
- Volvo XC90 (2003–)2012Alle motorer unntatt: B5254T2, B6324S5
Hva betyr feilkoden?
The engine control module monitors the pump current of the oxygen sensor. The code is set when current is detected in the pump current circuit while the sensor is cold, which points to leakage current or flashover in the wiring. The fault can also come from an internal fault in the control module.
Mulige årsaker
- Short circuit or flashover in the pump current wires
- Fault inside the engine control module (ECM) itself
Hva du kan gjøre
- 1Let the car stand until cold, start the engine and see whether the code returns
- 2With the car switched off, use a multimeter to check that the pump current wires have no contact with each other or with other wires
- 3Look for chafed wires and for moisture or dirt at the oxygen sensor connector, which can cause leakage current
- 4If the wires are intact but the fault remains, have a workshop check the control module with diagnostic equipment
Symptomer du kan merke1
- Message in the information display
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.