VOLVO
ECM-28A0 - Heated oxygen sensor (HO2S). Signal too low
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
8 modellerC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Vis modeller per årsmodell og motor (20)
- Volvo C30 (2007–2013)2007Kun motor: D5244T8, D5244T9
- Volvo C30 (2007–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo C70 (2006–2013)2007Kun motor: D5244T8, D5244T9
- Volvo C70 (2006–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo S40 (2004–2013)2006Kun motor: D5244T8
- Volvo S40 (2004–2013)2007Kun motor: D5244T8, D5244T9
- Volvo S40 (2004–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo S60 (2001–2009)2006Kun motor: D5244T4, D5244T5, D5244T6, D5244T7
- Volvo S60 (2001–2009)2007–2009Kun motor: D5244T4, D5244T5, D5244T7
- Volvo V50 (2004–2013)2006Kun motor: D5244T8
- Volvo V50 (2004–2013)2007Kun motor: D5244T8, D5244T9
- Volvo V50 (2004–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo V70 (2000–2008)2006Kun motor: D5244T4, D5244T5, D5244T6, D5244T7
- Volvo V70 (2000–2008)2007Kun motor: D5244T4, D5244T5, D5244T7
- Volvo V70 (2000–2008)2008Kun motor: D5244T5, D5244T7
- Volvo V70 XC / XC70 (2001–2007)2006–2007Kun motor: D5244T4
- Volvo XC90 (2003–)2006–2007Kun motor: D5244T4
- Volvo XC90 (2003–)2008–2010Kun motor: D5244T4, D5244T5
- Volvo XC90 (2003–)2011Kun motor: D5244T18, D5244T4, D5244T5
- Volvo XC90 (2003–)2012Alle motorer unntatt: B5254T2, B6324S5
Hva betyr feilkoden?
Although the code is named signal too low, the control module has calculated an incorrect temperature for the oxygen sensor from its internal resistance, and the code is set when that calculated value is wrong. Causes may be a broken or shorted signal wire, a damaged sensor, or an internal fault in the control module.
Mulige årsaker
- Open circuit in the signal cable
- Short circuit between the signal cables
- Damaged oxygen sensor
- Fault inside the engine control module (ECM) itself
Hva du kan gjøre
- 1Read the code, clear it and run the engine for a while to see whether it returns
- 2Switch off the ignition and check the oxygen sensor connections: they should be secure and free from play, contact resistance and oxidation
- 3With the car switched off, use a multimeter to check that the signal wire is not broken and the two signal wires are not shorted to each other
- 4If the connections and wiring are in order but the fault remains, have a workshop check the sensor and the control module with diagnostic equipment
Symptomer du kan merke1
- Message in the information display
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.