VOLVO
ECM-28E0 - Heated oxygen sensor (HO2S). Signal too low
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
8 modellerC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Vis modeller per årsmodell og motor (20)
- Volvo C30 (2007–2013)2007Kun motor: D5244T8, D5244T9
- Volvo C30 (2007–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo C70 (2006–2013)2007Kun motor: D5244T8, D5244T9
- Volvo C70 (2006–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo S40 (2004–2013)2006Kun motor: D5244T8
- Volvo S40 (2004–2013)2007Kun motor: D5244T8, D5244T9
- Volvo S40 (2004–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo S60 (2001–2009)2006Kun motor: D5244T4, D5244T5, D5244T6, D5244T7
- Volvo S60 (2001–2009)2007–2009Kun motor: D5244T4, D5244T5, D5244T7
- Volvo V50 (2004–2013)2006Kun motor: D5244T8
- Volvo V50 (2004–2013)2007Kun motor: D5244T8, D5244T9
- Volvo V50 (2004–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo V70 (2000–2008)2006Kun motor: D5244T4, D5244T5, D5244T6, D5244T7
- Volvo V70 (2000–2008)2007Kun motor: D5244T4, D5244T5, D5244T7
- Volvo V70 (2000–2008)2008Kun motor: D5244T5, D5244T7
- Volvo V70 XC / XC70 (2001–2007)2006–2007Kun motor: D5244T4
- Volvo XC90 (2003–)2006–2007Kun motor: D5244T4
- Volvo XC90 (2003–)2008–2010Kun motor: D5244T4, D5244T5
- Volvo XC90 (2003–)2011Kun motor: D5244T18, D5244T4, D5244T5
- Volvo XC90 (2003–)2012Alle motorer unntatt: B5254T2, B6324S5
Hva betyr feilkoden?
The engine control module takes its fuel and air mixture information from the oxygen sensor. The code is set when the signal for oxygen content is judged incorrect, here too low. The fault is detected while the engine runs under light load. The cause may be a short to ground in the signal wire, a damaged sensor or a fault inside the control module.
Mulige årsaker
- Signal wire shorted to ground
- Oxygen sensor damaged
- Control module has an internal fault
Hva du kan gjøre
- 1Read the code, clear it and drive with light load to see whether it returns
- 2Switch off the ignition, loosen the oxygen sensor connector and check it is clean, with no play or oxidation
- 3With the car switched off, use a multimeter to check that the signal wire has no contact with ground
- 4If you have a diagnostic tool: see in live data whether the oxygen sensor value changes while the engine runs under light load
- 5If the connector and wire are intact but the fault remains, have a workshop check the sensor and the control module with diagnostic equipment
Symptomer du kan merke1
- Message in the information display
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.