VOLVO
ECM-291C - Fuel pump control module. Signal too high
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
9 modellerC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Vis modeller per årsmodell og motor (23)
- Volvo C30 (2007–2013)2007Kun motor: B5254T3
- Volvo C30 (2007–2013)2008–2013Kun motor: B5254T7
- Volvo C70 (2006–2013)2006–2007Kun motor: B5254T3
- Volvo C70 (2006–2013)2008–2013Kun motor: B5254T7
- Volvo S40 (2004–2013)2005–2007Kun motor: B5254T3
- Volvo S40 (2004–2013)2008Kun motor: B5254T3, B5254T7
- Volvo S40 (2004–2013)2009–2012Kun motor: B5254T7
- Volvo S60 (2001–2009)2005–2006Kun motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2007Kun motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2008–2009Kun motor: B5204T5, B5244T5, B5254T2
- Volvo S80 (1999–2006)2005–2006Kun motor: B5204T5, B5244T4, B5254T2, B6294S2, B6294T
- Volvo V50 (2004–2013)2005–2007Kun motor: B5254T3
- Volvo V50 (2004–2013)2008–2012Kun motor: B5254T7
- Volvo V70 (2000–2008)2005Kun motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2006–2007Kun motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2008Kun motor: B5254T2
- Volvo V70 XC / XC70 (2001–2007)2005Alle motorer unntatt: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Kun motor: B5244T4, B5254T2
- Volvo V70 XC / XC70 (2001–2007)2007Kun motor: B5254T2
- Volvo XC90 (2003–)2005–2006Kun motor: B5254T2, B6294T
- Volvo XC90 (2003–)2007–2012Kun motor: B5254T2
- Volvo XC90 (2003–)2013–2014Kun motor: B5254T9
- Volvo XC90 (2003–)2015
Hva betyr feilkoden?
The engine control module (ECM) requests fuel pressure from the fuel pump control module through a pulse width modulated (PWM) signal, and that module then drives the pump to match the request. The code is set when the signal between the two modules is too high. It can only be read while the engine is running.
Mulige årsaker
- Signal wire between the ECM and the fuel pump control module shorted to supply voltage
- Damaged fuel pump control module
- Damaged supply wire to the fuel pump control module
- Poor contact, oxidation or looseness in connectors and joints
- Damaged fuel pump or damaged ground connection to the pump
Hva du kan gjøre
- 1Find out whether the fault is permanent or intermittent; if the engine runs normally now, the fault is likely temporary
- 2Inspect the plugs at the fuel pump control module for oxidation and poor contact
- 3Check the power feed to the fuel pump control module and the pump itself, including the relay and fuse
- 4Check the ground connection to the pump control module and the fuel pump
- 5Read the codes in the central electronic module, as this code is often a knock-on effect of electrical faults, and check the signal wire with diagnostic equipment
Symptomer du kan merke5
- The engine does not start even though the starter motor turns
- The engine stalls
- Lack of power and poor performance, especially when starting off
- Jerky running, hesitation or surging on acceleration or deceleration
- Engine warning lamp (Check Engine) lit
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.