VOLVO
ECM-2A50 - Pressure sensor particulate trap. Faulty signal
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Feilkoden har ulik betydning avhengig av modell, årsmodell eller motor. Velg betydningen som gjelder din bil.
Gjelder følgende modeller:
8 modellerC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Vis modeller per årsmodell og motor (20)
- Volvo C30 (2007–2013)2007Kun motor: D5244T8, D5244T9
- Volvo C30 (2007–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo C70 (2006–2013)2007Kun motor: D5244T8, D5244T9
- Volvo C70 (2006–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo S40 (2004–2013)2006Kun motor: D5244T8
- Volvo S40 (2004–2013)2007Kun motor: D5244T8, D5244T9
- Volvo S40 (2004–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo S60 (2001–2009)2006Kun motor: D5244T4, D5244T5, D5244T6, D5244T7
- Volvo S60 (2001–2009)2007–2009Kun motor: D5244T4, D5244T5, D5244T7
- Volvo V50 (2004–2013)2006Kun motor: D5244T8
- Volvo V50 (2004–2013)2007Kun motor: D5244T8, D5244T9
- Volvo V50 (2004–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo V70 (2000–2008)2006Kun motor: D5244T4, D5244T5, D5244T6, D5244T7
- Volvo V70 (2000–2008)2007Kun motor: D5244T4, D5244T5, D5244T7
- Volvo V70 (2000–2008)2008Kun motor: D5244T5, D5244T7
- Volvo V70 XC / XC70 (2001–2007)2006–2007Kun motor: D5244T4
- Volvo XC90 (2003–)2006–2007Kun motor: D5244T4
- Volvo XC90 (2003–)2008–2010Kun motor: D5244T4, D5244T5
- Volvo XC90 (2003–)2011Kun motor: D5244T18, D5244T4, D5244T5
- Volvo XC90 (2003–)2012Alle motorer unntatt: B5254T2, B6324S5
Hva betyr feilkoden?
The engine control module (ECM) has registered that the signal from the particulate trap pressure sensor is faulty. The fault can be caused by clogged or swapped hoses, a damaged sensor, or poor contact in the sensor connector.
Mulige årsaker
- Clogged hoses to the particulate trap pressure sensor
- Hoses to the pressure sensor have been swapped
- Damaged pressure sensor
- Contact resistance or oxidation in the connector
Hva du kan gjøre
- 1Make sure the hoses to the sensor are routed correctly and not blocked
- 2Clear the fault code and road test to see whether it returns
- 3If you have a diagnostic tool: read the pressure sensor value in live data with ignition on and then at idle, and compare it with what you expect
- 4Check the connector at the pressure sensor for loose contact, contact resistance and oxidation
- 5If the fault remains after these checks, the sensor may be damaged, and a workshop should check it and reset the adaptation
Symptomer du kan merke1
- Poor performance
Hva feilen kan påvirke1
- Engine output and engine speed are limited
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.