VOLVO
ECM-303D - Front knock sensor (KS). Signal too low
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
9 modellerC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Vis modeller per årsmodell og motor (23)
- Volvo C30 (2007–2013)2007Kun motor: B5254T3
- Volvo C30 (2007–2013)2008–2013Kun motor: B5254T7
- Volvo C70 (2006–2013)2006–2007Kun motor: B5254T3
- Volvo C70 (2006–2013)2008–2013Kun motor: B5254T7
- Volvo S40 (2004–2013)2005–2007Kun motor: B5254T3
- Volvo S40 (2004–2013)2008Kun motor: B5254T3, B5254T7
- Volvo S40 (2004–2013)2009–2012Kun motor: B5254T7
- Volvo S60 (2001–2009)2005–2006Kun motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2007Kun motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2008–2009Kun motor: B5204T5, B5244T5, B5254T2
- Volvo S80 (1999–2006)2005–2006Kun motor: B5204T5, B5244T4, B5254T2, B6294S2, B6294T
- Volvo V50 (2004–2013)2005–2007Kun motor: B5254T3
- Volvo V50 (2004–2013)2008–2012Kun motor: B5254T7
- Volvo V70 (2000–2008)2005Kun motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2006–2007Kun motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2008Kun motor: B5254T2
- Volvo V70 XC / XC70 (2001–2007)2005Alle motorer unntatt: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Kun motor: B5244T4, B5254T2
- Volvo V70 XC / XC70 (2001–2007)2007Kun motor: B5254T2
- Volvo XC90 (2003–)2005–2006Kun motor: B5254T2, B6294T
- Volvo XC90 (2003–)2007–2012Kun motor: B5254T2
- Volvo XC90 (2003–)2013–2014Kun motor: B5254T9
- Volvo XC90 (2003–)2015
Hva betyr feilkoden?
Under certain operating conditions the control module monitors the front knock sensor signal. If the signal is too low, the code is stored, and it can be checked while the engine runs. Poor contact at the sensor connection or a broken signal wire are common causes of a signal that is too weak.
Mulige årsaker
- Contact resistance in the knock sensor terminals
- Open circuit in the signal wire
- Short circuit between the knock sensor signal wires
- Damaged knock sensor
Hva du kan gjøre
- 1Check the knock sensor connector for poor contact and oxidation, and make sure it is firmly seated
- 2Check that the knock sensor is firmly fitted to the engine
- 3Read and clear the fault code, run the engine and check whether it returns
- 4If you have a diagnostic tool, check in live data that the knock signal changes when the engine is briefly revved
- 5Use a multimeter to check that the signal wire is not broken and has no contact with ground
- 6If the fault remains after the wiring has been checked, have a workshop replace or check the knock sensor
Symptomer du kan merke1
- Poor performance
Hva feilen kan påvirke2
- Ignition advance is pulled back to protect the engine
- Boost pressure is reduced
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.