VOLVO
ECM-433B - Leak diagnostic unit, pump. Signal missing
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
9 modellerC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Vis modeller per årsmodell og motor (23)
- Volvo C30 (2007–2013)2007Kun motor: B5254T3
- Volvo C30 (2007–2013)2008–2013Kun motor: B5254T7
- Volvo C70 (2006–2013)2006–2007Kun motor: B5254T3
- Volvo C70 (2006–2013)2008–2013Kun motor: B5254T7
- Volvo S40 (2004–2013)2005–2007Kun motor: B5254T3
- Volvo S40 (2004–2013)2008Kun motor: B5254T3, B5254T7
- Volvo S40 (2004–2013)2009–2012Kun motor: B5254T7
- Volvo S60 (2001–2009)2005–2006Kun motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2007Kun motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2008–2009Kun motor: B5204T5, B5244T5, B5254T2
- Volvo S80 (1999–2006)2005–2006Kun motor: B5204T5, B5244T4, B5254T2, B6294S2, B6294T
- Volvo V50 (2004–2013)2005–2007Kun motor: B5254T3
- Volvo V50 (2004–2013)2008–2012Kun motor: B5254T7
- Volvo V70 (2000–2008)2005Kun motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2006–2007Kun motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2008Kun motor: B5254T2
- Volvo V70 XC / XC70 (2001–2007)2005Alle motorer unntatt: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Kun motor: B5244T4, B5254T2
- Volvo V70 XC / XC70 (2001–2007)2007Kun motor: B5254T2
- Volvo XC90 (2003–)2005–2006Kun motor: B5254T2, B6294T
- Volvo XC90 (2003–)2007–2012Kun motor: B5254T2
- Volvo XC90 (2003–)2013–2014Kun motor: B5254T9
- Volvo XC90 (2003–)2015
Hva betyr feilkoden?
The engine control module receives no signal from the leak diagnostic pump, and the fault code is set. The fault can be caused by poor contact, an open circuit in the signal or supply wire, or a damaged pump. The leak diagnostic is switched off while the fault is present.
Mulige årsaker
- Contact resistance in the connections
- Open circuit in the signal wire
- Open circuit in the supply wire
- Damaged pump in the leak diagnostic unit
Hva du kan gjøre
- 1Check the connector of the leak diagnostic unit for contact resistance and oxidation
- 2Use a multimeter to check that the signal and supply wires are not open-circuited
- 3Look for chafed or pinched wiring to the leak diagnostic unit
- 4Have you got a diagnostic tool: check in live data that the pump signal is present when the leak diagnostic runs
- 5Have a workshop replace the pump in the leak diagnostic unit if the wiring is intact but the signal is still missing
Symptomer du kan merke1
- Malfunction indicator lamp (MIL) is on
Hva feilen kan påvirke1
- The leak diagnostic is switched off
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.