VOLVO
ECM-580F - Configuration fault. Faulty signal
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Feilkoden har ulik betydning avhengig av modell, årsmodell eller motor. Velg betydningen som gjelder din bil.
Gjelder følgende modeller:
8 modellerC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Vis modeller per årsmodell og motor (20)
- Volvo C30 (2007–2013)2007Kun motor: D5244T8, D5244T9
- Volvo C30 (2007–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo C70 (2006–2013)2007Kun motor: D5244T8, D5244T9
- Volvo C70 (2006–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo S40 (2004–2013)2006Kun motor: D5244T8
- Volvo S40 (2004–2013)2007Kun motor: D5244T8, D5244T9
- Volvo S40 (2004–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo S60 (2001–2009)2006Kun motor: D5244T4, D5244T5, D5244T6, D5244T7
- Volvo S60 (2001–2009)2007–2009Kun motor: D5244T4, D5244T5, D5244T7
- Volvo V50 (2004–2013)2006Kun motor: D5244T8
- Volvo V50 (2004–2013)2007Kun motor: D5244T8, D5244T9
- Volvo V50 (2004–2013)2008–2010Kun motor: D5244T13, D5244T8, D5244T9
- Volvo V70 (2000–2008)2006Kun motor: D5244T4, D5244T5, D5244T6, D5244T7
- Volvo V70 (2000–2008)2007Kun motor: D5244T4, D5244T5, D5244T7
- Volvo V70 (2000–2008)2008Kun motor: D5244T5, D5244T7
- Volvo V70 XC / XC70 (2001–2007)2006–2007Kun motor: D5244T4
- Volvo XC90 (2003–)2006–2007Kun motor: D5244T4
- Volvo XC90 (2003–)2008–2010Kun motor: D5244T4, D5244T5
- Volvo XC90 (2003–)2011Kun motor: D5244T18, D5244T4, D5244T5
- Volvo XC90 (2003–)2012Alle motorer unntatt: B5254T2, B6324S5
Hva betyr feilkoden?
The engine control module (ECM) gets setup data for the car over CAN from the central electronic module (CEM). The code is set when that signal is missing or faulty. Causes may be CAN faults, connector problems, or a used CEM that does not suit the car. The driver normally does not notice the fault.
Mulige årsaker
- Signal from the CEM is missing or faulty
- Raised contact resistance or oxidation in the connector terminals
- Break in the CAN wiring to the central electronic module (CEM)
- Internal fault in another module on the same part of the CAN network
- CAN-related fault codes stored in the CEM
- The central electronic module (CEM) is not intended for this car, for example if a used module with other software or hardware has been fitted
Hva du kan gjøre
- 1Read the CAN-related codes in the central electronic module (CEM) and fix them first
- 2Check that the connectors on the CAN network between the modules are fully seated and free from oxidation
- 3With a multimeter, check that the CAN wires are not broken
- 4If the car has been fitted with a used control module, have a workshop check that it is right for the car
Symptomer du kan merke1
- No noticeable symptoms for the driver
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.