VOLVO
ECM-921C - Electronic throttle unit, potentiometer 1. Signal too high
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
9 modellerC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Vis modeller per årsmodell og motor (23)
- Volvo C30 (2007–2013)2007Kun motor: B5254T3
- Volvo C30 (2007–2013)2008–2013Kun motor: B5254T7
- Volvo C70 (2006–2013)2006–2007Kun motor: B5254T3
- Volvo C70 (2006–2013)2008–2013Kun motor: B5254T7
- Volvo S40 (2004–2013)2005–2007Kun motor: B5254T3
- Volvo S40 (2004–2013)2008Kun motor: B5254T3, B5254T7
- Volvo S40 (2004–2013)2009–2012Kun motor: B5254T7
- Volvo S60 (2001–2009)2005–2006Kun motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2007Kun motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2008–2009Kun motor: B5204T5, B5244T5, B5254T2
- Volvo S80 (1999–2006)2005–2006Kun motor: B5204T5, B5244T4, B5254T2, B6294S2, B6294T
- Volvo V50 (2004–2013)2005–2007Kun motor: B5254T3
- Volvo V50 (2004–2013)2008–2012Kun motor: B5254T7
- Volvo V70 (2000–2008)2005Kun motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2006–2007Kun motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2008Kun motor: B5254T2
- Volvo V70 XC / XC70 (2001–2007)2005Alle motorer unntatt: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Kun motor: B5244T4, B5254T2
- Volvo V70 XC / XC70 (2001–2007)2007Kun motor: B5254T2
- Volvo XC90 (2003–)2005–2006Kun motor: B5254T2, B6294T
- Volvo XC90 (2003–)2007–2012Kun motor: B5254T2
- Volvo XC90 (2003–)2013–2014Kun motor: B5254T9
- Volvo XC90 (2003–)2015
Hva betyr feilkoden?
The engine control module (ECM) has registered that the signal from potentiometer 1, the first throttle position sensor, is too high, and the code is set. The cause can be poor contact, an open or voltage-shorted signal cable, or an open earth lead to the potentiometers.
Mulige årsaker
- Contact resistance or oxidation between the ECM and the throttle unit
- Signal cable has an open circuit or is short-circuited to voltage
- Open circuit in the earth lead to potentiometers 1 and 2
- Damaged throttle unit
Hva du kan gjøre
- 1Check the connectors between the ECM and the throttle unit for contact resistance and oxidation
- 2Use a multimeter to check that the earth lead to the throttle unit potentiometers has no open circuit
- 3Use a multimeter to check that the signal cable has no open circuit and is not short-circuited to voltage
- 4If nothing is found and the code returns as permanent, have a workshop replace the throttle unit and carry out the adaptation
Symptomer du kan merke1
- The engine responds to the accelerator less well than normal
Hva feilen kan påvirke2
- Potentiometer 2 takes over the throttle angle calculation
- When potentiometers 1 and 2 both report faults together, the throttle motor loses its supply and the throttle returns to rest
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.