VOLVO
ECM-922D - Electronic throttle unit, potentiometer 2. Signal too low
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
9 modellerC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Vis modeller per årsmodell og motor (23)
- Volvo C30 (2007–2013)2007Kun motor: B5254T3
- Volvo C30 (2007–2013)2008–2013Kun motor: B5254T7
- Volvo C70 (2006–2013)2006–2007Kun motor: B5254T3
- Volvo C70 (2006–2013)2008–2013Kun motor: B5254T7
- Volvo S40 (2004–2013)2005–2007Kun motor: B5254T3
- Volvo S40 (2004–2013)2008Kun motor: B5254T3, B5254T7
- Volvo S40 (2004–2013)2009–2012Kun motor: B5254T7
- Volvo S60 (2001–2009)2005–2006Kun motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2007Kun motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2008–2009Kun motor: B5204T5, B5244T5, B5254T2
- Volvo S80 (1999–2006)2005–2006Kun motor: B5204T5, B5244T4, B5254T2, B6294S2, B6294T
- Volvo V50 (2004–2013)2005–2007Kun motor: B5254T3
- Volvo V50 (2004–2013)2008–2012Kun motor: B5254T7
- Volvo V70 (2000–2008)2005Kun motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2006–2007Kun motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2008Kun motor: B5254T2
- Volvo V70 XC / XC70 (2001–2007)2005Alle motorer unntatt: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Kun motor: B5244T4, B5254T2
- Volvo V70 XC / XC70 (2001–2007)2007Kun motor: B5254T2
- Volvo XC90 (2003–)2005–2006Kun motor: B5254T2, B6294T
- Volvo XC90 (2003–)2007–2012Kun motor: B5254T2
- Volvo XC90 (2003–)2013–2014Kun motor: B5254T9
- Volvo XC90 (2003–)2015
Hva betyr feilkoden?
The engine control module (ECM) monitors the signal from potentiometer 2, the second throttle position sensor, which is too low, and sets the code. The cause can be poor contact, a signal cable shorted to ground or open, or a supply to the potentiometers that is open or shorted to ground.
Mulige årsaker
- Contact resistance or oxidation between the ECM and the throttle unit
- Signal cable short-circuited to ground or open circuit
- Open circuit or short-circuit to ground in the supply to potentiometers 1 and 2
- Damaged throttle unit
Hva du kan gjøre
- 1Check the connectors between the ECM and the throttle unit for contact resistance and oxidation
- 2Use a multimeter to check that the signal cable is not short-circuited to ground and has no open circuit
- 3Use a multimeter to check that the supply to the potentiometers has no open circuit and is not short-circuited to ground
- 4If the fault remains after these checks, the throttle unit may need replacing by a workshop, which also carries out the adaptation
Symptomer du kan merke1
- The car's performance is reduced
Hva feilen kan påvirke2
- Potentiometer 1 takes over the throttle angle calculation
- If potentiometer 1 also has a fault, its code is set too, and if both are stored the supply to the throttle motor is switched off
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.