VOLVO
ECM-926C - Electronic throttle unit. Signal too high
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
9 modellerC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Vis modeller per årsmodell og motor (23)
- Volvo C30 (2007–2013)2007Kun motor: B5254T3
- Volvo C30 (2007–2013)2008–2013Kun motor: B5254T7
- Volvo C70 (2006–2013)2006–2007Kun motor: B5254T3
- Volvo C70 (2006–2013)2008–2013Kun motor: B5254T7
- Volvo S40 (2004–2013)2005–2007Kun motor: B5254T3
- Volvo S40 (2004–2013)2008Kun motor: B5254T3, B5254T7
- Volvo S40 (2004–2013)2009–2012Kun motor: B5254T7
- Volvo S60 (2001–2009)2005–2006Kun motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2007Kun motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2008–2009Kun motor: B5204T5, B5244T5, B5254T2
- Volvo S80 (1999–2006)2005–2006Kun motor: B5204T5, B5244T4, B5254T2, B6294S2, B6294T
- Volvo V50 (2004–2013)2005–2007Kun motor: B5254T3
- Volvo V50 (2004–2013)2008–2012Kun motor: B5254T7
- Volvo V70 (2000–2008)2005Kun motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2006–2007Kun motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2008Kun motor: B5254T2
- Volvo V70 XC / XC70 (2001–2007)2005Alle motorer unntatt: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Kun motor: B5244T4, B5254T2
- Volvo V70 XC / XC70 (2001–2007)2007Kun motor: B5254T2
- Volvo XC90 (2003–)2005–2006Kun motor: B5254T2, B6294T
- Volvo XC90 (2003–)2007–2012Kun motor: B5254T2
- Volvo XC90 (2003–)2013–2014Kun motor: B5254T9
- Volvo XC90 (2003–)2015
Hva betyr feilkoden?
The code means the signal from the throttle unit is too high. It is stored when the engine control module (ECM) attempts to adapt the throttle unit and finds restricted throttle movement, or an opening spring that is not working properly.
Mulige årsaker
- The throttle is sticking or blocked by oil film, dust or similar
- Contact resistance or oxidation linking the ECM to the throttle unit
- Open circuit, or short to ground or supply voltage, in the wiring to the throttle motor
- Short circuit between the wires to the throttle motor
- A damaged throttle unit
Hva du kan gjøre
- 1Read the fault codes and deal first with any that relate to the throttle unit, throttle position sensor or ECM, as they may be the cause
- 2Look for anything blocking the throttle and check that it is not sticking. Clean as needed
- 3Check the connectors between the ECM and the throttle unit: are they secure, and is there corrosion
- 4Use a multimeter on the throttle motor wiring for open circuit, contact with ground or supply voltage, and a short between the two wires
- 5If you have a diagnostic tool: follow the throttle angle in live data while the pedal is pressed and released. It should change smoothly, without jumps
- 6If the code returns, this points to a damaged throttle unit, which then needs replacing and adapting. A workshop with diagnostic equipment does this
Symptomer du kan merke2
- Malfunction indicator lamp (MIL) on
- Reduced engine performance
Hva feilen kan påvirke1
- Depending on the fault, the ECM may cut the supply to the throttle motor so that the throttle goes to its spring-loaded position
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.