VOLVO
ECM-B10E813 - Secondary Battery Relay "A". General Electrical Failures. Circuit open
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
12 modellerC30 (2007–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–)
Vis modeller per årsmodell og motor (25)
- Volvo C30 (2007–2013)2011–2013Kun motor: D4162T
- Volvo S40 (2004–2013)2011–2012Kun motor: D4162T
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, D4162T
- Volvo S60 (2011–)2012Alle motorer unntatt: B4204T7, B5254T5, B6304T4
- Volvo S60 (2011–)2013–2014Alle motorer unntatt: B4204T7, B6304T4
- Volvo S60 (2011–)2015Alle motorer unntatt: B6304T3, B6304T4, B6304T5
- Volvo S80 (2007–)2011Kun motor: B4164T
- Volvo S80 (2007–)2012Kun motor: B4164T, B4164T2, D4162T, D5204T3, D5244T11, D5244T15
- Volvo S80 (2007–)2013–2014Alle motorer unntatt: B4204T6, B4204T7, B6304T4, B6324S4, B6324S5
- Volvo S80 (2007–)2015Alle motorer unntatt: B6304T4, B6324S4, B6324S5
- Volvo V40 (2013–)2013–2015
- Volvo V40 Cross Country (2013–)2013–2015
- Volvo V50 (2004–2013)2011–2012Kun motor: D4162T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, D4162T
- Volvo V60 (2011–)2012Alle motorer unntatt: B4204T7, B6304T4
- Volvo V60 (2011–)2013–2014Alle motorer unntatt: B4204T7, B6304T4, D82PHEV
- Volvo V60 (2011–)2015Alle motorer unntatt: B6304T3, B6304T4, B6304T5, D82PHEV, D87PHEV
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2011Kun motor: B4164T
- Volvo V70 (2008–)2012Alle motorer unntatt: B4204T7, B5254T10, B6304T4, B6324S5
- Volvo V70 (2008–)2013–2014Alle motorer unntatt: B4204T7, B6304T4, B6324S5
- Volvo V70 (2008–)2015Alle motorer unntatt: B6304T4
- Volvo XC60 (2009–)2012Kun motor: D5204T3, D5244T11, D5244T15, D5244T17
- Volvo XC60 (2009–)2013–2015Alle motorer unntatt: B4204T7, B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2012–2015Alle motorer unntatt: B6304T4, B6324S4, B6324S5
Hva betyr feilkoden?
The engine control module monitors the secondary battery relay, which connects the secondary battery during an engine start after auto-stop. The code is set when the signal wire between the engine control module and the relay has an open circuit, and automatic start and stop is then switched off.
Mulige årsaker
- Loose or oxidised connector
- Open circuit in the signal wire
- Damaged secondary battery relay
Hva du kan gjøre
- 1Check that the relevant fuses are intact and that the connector at the relay is fully seated
- 2With a multimeter, check that the signal wire between the engine control module and the relay is not broken
- 3If the wire is sound, the relay is probably damaged and should be replaced by a workshop
Symptomer du kan merke2
- Automatic start/stop of the engine does not work while driving
- Automatic start/stop of the engine does not work at idle
Hva feilen kan påvirke1
- The automatic engine start/stop function is switched off
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.