VOLVO
ECM-P001500 - Exhaust (B) Camshaft Position Timing - Over-Retarded (Bank 1). General Failure Information. No sub type information
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Feilkoden har ulik betydning avhengig av modell, årsmodell eller motor. Velg betydningen som gjelder din bil.
Gjelder følgende modeller:
9 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–)
Vis modeller per årsmodell og motor (18)
- Volvo S60 (2011–)2013Kun motor: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo S60 (2011–)2014–2015Kun motor: B4204T10, B4204T11, B4204T12, B4204T15, B4204T9, B5204T8, B5204T9, B5254T12, B5254T14
- Volvo S80 (2007–)2013Kun motor: B5254T12, B5254T14
- Volvo S80 (2007–)2014Kun motor: B4204T11, B4204T12, B4204T15, B5254T12, B5254T14
- Volvo S80 (2007–)2015Kun motor: B4204T11, B4204T12, B4204T15
- Volvo V40 (2013–)2013–2014Kun motor: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V40 (2013–)2015Kun motor: B4204T11, B5204T8, B5204T9
- Volvo V40 Cross Country (2013–)2013–2014Kun motor: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V40 Cross Country (2013–)2015Alle motorer unntatt: B4164T, D4162T, D4204T14, D5204T6
- Volvo V60 (2011–)2013Kun motor: B5204T8, B5204T9
- Volvo V60 (2011–)2014Kun motor: B4204T11, B4204T12, B4204T15, B4204T9, B5204T8, B5204T9, B5254T12
- Volvo V60 (2011–)2015Kun motor: B4204T11, B4204T12, B4204T15, B4204T9, B5204T9, B5254T12
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2013Kun motor: B5204T9
- Volvo V70 (2008–)2014–2015Kun motor: B4204T11, B5204T9
- Volvo XC60 (2009–)2014Kun motor: B4204T10, B4204T11, B4204T12, B4204T15, B4204T9
- Volvo XC60 (2009–)2015Kun motor: B4204T10, B4204T11, B4204T12, B4204T15, B4204T9, B5204T9, B5254T12, B5254T14
- Volvo XC70 (2008–)2014–2015Kun motor: B4204T11
Hva betyr feilkoden?
The code name says the exhaust camshaft is too far retarded, but it is really set when control is too slow while the camshaft is being advanced. The engine control module compares the camshaft position with the commanded position, bank 1. The code is set when the engine is warm, the engine speed is above a certain level and camshaft control is active.
Mulige årsaker
- Poor quality engine oil
- Low oil pressure
- Damaged exhaust camshaft control valve
- Damaged VVT unit
Hva du kan gjøre
- 1If there is a stored code for the crankshaft-to-camshaft correlation, diagnose that one first
- 2Check that the engine oil level is correct and that the oil is clean and of the right quality
- 3If you have a diagnostic tool: activate exhaust camshaft control and see whether it responds
- 4Have a workshop remove the control valve for cleaning and check the oil passages in the cylinder head
- 5If the fault remains: have a workshop fit a new control valve
- 6If the fault returns: have a workshop check whether the VVT unit is damaged internally
Symptomer du kan merke4
- The car lacks power, especially when pulling away from standstill
- Engine hesitates or runs jerkily on acceleration, when braking and at steady speed
- Uneven idle
- Check engine lamp lit or behaving abnormally
Hva feilen kan påvirke1
- The camshaft is returned to its basic position
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.