VOLVO
ECM-P001678 - Crankshaft Position - Camshaft Position Correlation - Bank 1 Sensor A. Mechanical Failures. Alignment or adjustment incorrect
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (27)
- Volvo S60 (2011–)2011Alle motorer unntatt: B6304T4, D4162T, D5204T2, D5244T10
- Volvo S60 (2011–)2012Kun motor: B4164T, B4164T2, B4164T3, B4204T7, B5254T5
- Volvo S60 (2011–)2013–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2007–2008Kun motor: B5254T6
- Volvo S80 (2007–)2009Kun motor: B5254T6, B5254T8
- Volvo S80 (2007–)2010Kun motor: B4204T6, B5254T10, B5254T11, B5254T8
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7, B5254T10, B5254T11, B5254T8
- Volvo S80 (2007–)2012Kun motor: B4164T, B4164T2, B4204T6, B4204T7, B5254T10
- Volvo S80 (2007–)2013–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2008Kun motor: B5254T6
- Volvo V70 (2008–)2009Kun motor: B5254T6, B5254T8
- Volvo V70 (2008–)2010Kun motor: B4204T6, B5254T10, B5254T11
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7, B5254T10, B5254T11
- Volvo V70 (2008–)2012Kun motor: B4164T, B4164T2, B4204T7, B5254T10
- Volvo V70 (2008–)2013–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
The engine control module checks the camshaft position against the crankshaft position. If the camshaft is behind the crankshaft and the adaptation falls below a certain value, the code is set. It is a mechanical fault in timing or adjustment, and it is tested when the engine is warm and idling.
Mulige årsaker
- Poor quality engine oil
- Incorrectly set camshafts
- Timing belt has skipped teeth
- Worn teeth on the timing belt
- Camshaft incorrectly fitted
- Damaged camshaft
Hva du kan gjøre
- 1Check the engine oil level and quality, especially if it may be contaminated
- 2If you have a diagnostic tool: activate camshaft control and check that it responds
- 3Have a workshop check that the camshaft is fitted correctly and that the timing belt is not displaced or worn
- 4Have a workshop remove the control valve for cleaning and check the oil passages in the cylinder head
- 5If the fault remains: have a workshop adjust the camshaft setting or try a new control valve
Symptomer du kan merke4
- Engine is hard to start and cranks slowly
- The car lacks power
- Engine hesitates or runs jerkily on acceleration
- Check engine lamp lit or behaving abnormally
Hva feilen kan påvirke1
- Camshaft control is switched off
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.