VOLVO
ECM-P001778 - Crankshaft Position - Camshaft Position Correlation - Bank 1 Sensor B. Mechanical Failures. Alignment or adjustment incorrect
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (27)
- Volvo S60 (2011–)2011Alle motorer unntatt: B6304T4, D4162T, D5204T2, D5244T10
- Volvo S60 (2011–)2012Kun motor: B4164T, B4164T2, B4164T3, B4204T7, B5254T5
- Volvo S60 (2011–)2013–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2007–2008Kun motor: B5254T6
- Volvo S80 (2007–)2009Kun motor: B5254T6, B5254T8
- Volvo S80 (2007–)2010Kun motor: B4204T6, B5254T10, B5254T11, B5254T8
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7, B5254T10, B5254T11, B5254T8
- Volvo S80 (2007–)2012Kun motor: B4164T, B4164T2, B4204T6, B4204T7, B5254T10
- Volvo S80 (2007–)2013–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2008Kun motor: B5254T6
- Volvo V70 (2008–)2009Kun motor: B5254T6, B5254T8
- Volvo V70 (2008–)2010Kun motor: B4204T6, B5254T10, B5254T11
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7, B5254T10, B5254T11
- Volvo V70 (2008–)2012Kun motor: B4164T, B4164T2, B4204T7, B5254T10
- Volvo V70 (2008–)2013–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
The engine control module checks the camshaft positions relative to the crankshaft. The code concerns the exhaust camshaft, bank 1, sensor B, when it sits too far behind the crankshaft and the adaptation falls below a certain value. The fault is checked with the engine warm and at idle.
Mulige årsaker
- Incorrectly set camshafts
- Camshaft timing belt has skipped teeth
- Worn teeth on the camshaft belt
- Camshaft incorrectly fitted
- Damaged camshaft
Hva du kan gjøre
- 1Read the code, clear it and road test the car to see whether it returns
- 2Check the engine oil level and quality, and that it is free from contamination
- 3If you have a diagnostic tool: read the exhaust camshaft adaptation with the engine warm and idling
- 4Have a workshop check that the camshaft is fitted correctly and that the timing belt sits correctly without skipped teeth
- 5Have a workshop clean or replace the control valve, and adjust the camshaft setting if needed
- 6If the fault returns: have a workshop check the camshaft and the VVT unit
Symptomer du kan merke5
- Engine is hard to start
- The car lacks power
- Engine hesitates or runs jerkily
- Emissions warning lamp lit
- Check engine lamp lit or behaving abnormally
Hva feilen kan påvirke1
- Camshaft control is switched off
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.