VOLVO
ECM-P003613 - HO2S Heater Control Circuit (Bank 1, Sensor 2). General Electrical Failures. Circuit open
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (20)
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Kun motor: B4204T6
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Kun motor: B4204T6
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
The engine control module regulates the heating of the rear lambda sensor on bank 1, sensor 2, by pulsing the current to the sensor's PTC element. The code concerns an open circuit and is set when the signal falls below a set level while the heating is switched off.
Mulige årsaker
- Poor contact and oxidation in the connections
- Open circuit in the supply from the system relay
- Faulty rear lambda sensor
Hva du kan gjøre
- 1Read the code, clear it and road test the car to see whether it returns
- 2Check the connector at the rear lambda sensor for poor contact or oxidation, and do not use rust-release spray or grease in the connector
- 3Use a multimeter to check that the supply voltage from the system relay to the rear lambda sensor has no open circuit
- 4Have a workshop check the resistance of the lambda sensor
- 5If troubleshooting does not solve the fault: have a workshop try a new lambda sensor
Symptomer du kan merke1
- Check engine lamp lit or behaving abnormally
Hva feilen kan påvirke1
- Lambda control is switched off
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.