VOLVO
ECM-P007B17 - Charge Air Cooler Temperature Sensor Circuit Range/Performance (Bank 1). General Electrical Failures. Circuit voltage above threshold
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (20)
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Kun motor: B4204T6
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Kun motor: B4204T6
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
The boost pressure sensor (TMAP) measures both boost pressure and air temperature at the charge air cooler. The engine control module (ECM) stores the highest temperature at high boost and the lowest at low boost. The difference between them must be large enough. If it is too small, the sensor signal is considered unreliable and the fault code is set.
Mulige årsaker
- Contact resistance, oxidation or a loose connection at the boost pressure sensor
- Internal short circuit in the boost pressure sensor (TMAP)
- Damaged boost pressure sensor (TMAP)
Hva du kan gjøre
- 1Start with the boost pressure sensor connector: it should be secure, dry and free from corrosion
- 2Look for chafed or pinched wiring from the sensor
- 3If you have a diagnostic tool: read the boost pressure sensor temperature in live data with the engine running, and check that it changes clearly between idle and hard acceleration
- 4If the fault returns after the connector has been checked, have a workshop check the boost pressure sensor
Symptomer du kan merke1
- No noticeable symptoms for the driver
Hva feilen kan påvirke1
- The engine control module uses a calculated value instead of the measured temperature
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.