VOLVO
ECM-P007C11 - Charge Air Cooler Temperature Sensor Circuit Low (Bank 1). General Electrical Failures. Circuit short to ground
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (20)
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Kun motor: B4204T6
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Kun motor: B4204T6
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
The boost pressure sensor (TMAP) measures boost pressure and temperature at the charge air cooler. The fault code is set when the signal from the sensor is below a limit, which can be caused by a signal wire shorted to ground, poor contact or a damaged sensor.
Mulige årsaker
- Contact resistance, oxidation or loose connection in the connector
- Signal wire shorted to ground
- Damaged boost pressure sensor (TMAP)
Hva du kan gjøre
- 1Use a multimeter to check that the signal wire to the boost pressure sensor has no contact with ground (the body), with the ignition on
- 2Check the sensor connector for moisture, corrosion and loose connections
- 3Look for chafing in the sensor wiring, especially where it may have been pinched
- 4If you have a diagnostic tool: read the boost pressure sensor temperature in live data with the engine running and check whether it reads an unreasonably low value
- 5Have a workshop measure the sensor signal and replace the boost pressure sensor if the wiring is intact
Symptomer du kan merke1
- The Check engine warning lamp lights up
Hva feilen kan påvirke1
- The engine control module uses a calculated value instead of the measured temperature
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.