VOLVO
ECM-P008753 - Fuel Rail/System Pressure - Too Low. System Programming Failures. Deactivated
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (20)
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Kun motor: B4204T6
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Kun motor: B4204T6
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
This fault code concerns the high-pressure side of the fuel system. It is set when the measured fuel pressure is too low compared with the target value while the engine is cold and the catalyst is warming up. The code is marked as deactivated in the control module programming.
Mulige årsaker
- Leak in the fuel system
- Contact resistance or oxidation in the connections
- Signal wire shorted to voltage
- Open circuit in the signal wire or the signal ground wire
- Damaged fuel pressure sensor
- Damaged fuel pump
Hva du kan gjøre
- 1Make sure there is enough fuel in the tank
- 2Check the fuel lines for leaks
- 3Check the connectors at the fuel pressure sensor and the fuel pump for oxidation and loose contacts
- 4If you have a diagnostic tool: read the fuel pressure in live data when the engine is cold and compare it with the reading when warm
- 5Have a workshop with diagnostic equipment check that the fault code belongs to the correct programming, since it is deactivated
Symptomer du kan merke3
- Check engine lamp (MIL) lights up
- Uneven idle
- The engine may hesitate, surge or run jerkily while driving
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.