VOLVO
ECM-P010211 - Mass or Volume Air Flow A Circuit Low. General Electrical Failures. Circuit short to ground
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (20)
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Kun motor: B4204T6
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Kun motor: B4204T6
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
The ECM watches the mass air flow sensor signal and stores the code when the signal falls outside the normal range. In this case the fault is a short to ground, meaning the signal wire has made contact with the vehicle body. The result is that the engine works from a calculated air mass value and some monitoring functions are switched off.
Mulige årsaker
- Signal wire shorted to ground
- Loose or corroded connections
- Break in the signal wire
- Break in the voltage supply
- Contact resistance in the mass air flow sensor connector terminals
- Damaged mass air flow sensor
Hva du kan gjøre
- 1Read and note the code, clear it and road test to see whether it returns
- 2With a multimeter, check that the signal wire between the control module and the sensor has no break and is not touching ground
- 3Check that the connector at the mass air flow sensor is fully engaged and free from oxidation and play
- 4With a multimeter, check the supply wire from the system relay to the sensor for a break
- 5Look for chafed wiring that may have come into contact with the body
- 6If the fault remains, have a workshop check the mass air flow sensor
Symptomer du kan merke1
- The car lacks power and runs poorly
Hva feilen kan påvirke3
- A calculated air mass value is used
- Rear lambda sensor control is switched off
- Misfire diagnosis is switched off
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.