VOLVO
ECM-P010817 - Manifold Absolute Pressure/BARO Sensor High. General Electrical Failures. Circuit voltage above threshold
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (20)
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Kun motor: B4204T6
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Kun motor: B4204T6
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
The ECM measures the intake pressure with an air pressure sensor and checks the sensor's DC voltage. The code is stored when an incorrect value lasts for a set time or over three or more consecutive drive cycles.
Mulige årsaker
- Break in the signal or ground wire
- Contact resistance and oxidation in the connections
- Signal wire shorted to supply voltage
- Air pressure sensor in the intake pipe is damaged
Hva du kan gjøre
- 1Read and note the code, clear it and road test to see whether it returns
- 2With diagnostic equipment and the ignition on, compare the intake pressure in live data with ambient pressure; a clear difference suggests a faulty sensor
- 3Check that the connector at the sensor sits firmly and is free from oxidation and contact resistance
- 4With a multimeter, check that the signal wire is not shorted to supply voltage or ground
- 5If the fault remains and the sensor reading differs, have a workshop replace the sensor
Symptomer du kan merke1
- Engine warning lamp (check engine) lit or behaving abnormally
Hva feilen kan påvirke1
- The sensor signal is replaced by a constant intake air pressure value
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.