VOLVO
ECM-P013716 - O2 Sensor Circuit Low Voltage (Bank 1 Sensor 2). General Electrical Failures. Circuit voltage below threshold
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (20)
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Kun motor: B4204T6
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Kun motor: B4204T6
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
Although the code is named for a low voltage, it concerns the signal from the rear oxygen sensor in bank 1, sensor 2. The engine control module (ECM) monitors the sensor signal and sets the code when it deviates from its permitted range, or when the sensor's pre-heating voltage disturbs the signal. The rear sensor is used to check that the catalytic converter is working.
Mulige årsaker
- Signal wire shorted to ground
- Ground wire shorted to ground
- Damaged rear oxygen sensor
Hva du kan gjøre
- 1Read the code, clear it and road test the car to see whether it comes back
- 2Use a multimeter to check that the signal wire to the rear sensor is not shorted to ground
- 3Check the connector to the rear sensor for contact resistance and oxidation; do not use rust solvent spray or grease
- 4If the wires and connector are intact, replace the rear oxygen sensor
Symptomer du kan merke1
- Check engine light (MIL) on
Hva feilen kan påvirke2
- Control with the rear oxygen sensor is switched off
- Catalytic converter diagnostics are disabled
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.