VOLVO
ECM-P013817 - O2 Sensor Circuit High Voltage (Bank 1 Sensor 2). General Electrical Failures. Circuit voltage above threshold
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (20)
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Kun motor: B4204T6
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Kun motor: B4204T6
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
The engine control module (ECM) monitors the rear oxygen sensor in bank 1, sensor 2, by checking its signal while driving. It sets the code when the signal deviates from its permitted operating range or when the pre-heating voltage disturbs the signal. The cause may therefore be wires that have picked up voltage instead of running to their correct point, or a damaged sensor.
Mulige årsaker
- Signal wire shorted to supply voltage
- Ground wire shorted to supply voltage
- Damaged rear oxygen sensor
Hva du kan gjøre
- 1Read the code, clear it and road test the car to see whether it comes back
- 2Switch the ignition off and use a multimeter to check that the signal wire from the rear sensor has no contact with voltage
- 3Check that the ground wire has no contact with voltage, and inspect the connectors for contact resistance
- 4If the wires are intact, replace the rear oxygen sensor
Symptomer du kan merke1
- Check engine light (MIL) on
Hva feilen kan påvirke2
- Control with the rear oxygen sensor is switched off
- Catalytic converter diagnostics are disabled
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.