VOLVO
ECM-P025D12 - Fuel Pump A Control Circuit High. General Electrical Failures. Circuit short to battery
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (20)
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Kun motor: B4204T6
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Kun motor: B4204T6
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
Fuel pressure is regulated by the fuel pump control module, which receives a PWM signal from the ECM. The code is stored when that signal is too high, which is a general electrical fault. The causes are a signal wire short-circuited to supply voltage or a damaged fuel pump control module.
Mulige årsaker
- Signal wire short-circuited to supply voltage
- Damaged fuel pump control module
Hva du kan gjøre
- 1Read and note the fault code, clear it and test drive to see whether it returns
- 2If you have a diagnostic tool: activate the fuel pump with the ignition on and see whether it runs
- 3Check the connector to the fuel pump control module for contact resistance and oxidation
- 4With the ignition off and the connector disconnected, use a multimeter to check that the signal wire has no open circuit
- 5Have a workshop with diagnostic equipment check that the signal wire is not short-circuited to supply voltage and check the fuel pump control module
Symptomer du kan merke2
- The engine does not start but cranks
- The engine stalls while driving, at any time or all the time
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.