VOLVO
ECM-P032714 - Knock Sensor 1 Circuit Low (Bank1). General Electrical Failures. Circuit short to ground or open
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (20)
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Kun motor: B4204T6
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Kun motor: B4204T6
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
The signal from the left knock sensor is too low, which can be caused by the cable being short-circuited to ground or by a break (open circuit). The engine control module (ECM) compares the signal with its limit values and sets the fault code when the signal lies outside them.
Mulige årsaker
- Signal cable short-circuited to ground
- Contact resistance in the knock sensor connections
- Break in the signal cable
- Short circuit between the knock sensors' signal cables
- Damaged knock sensor
Hva du kan gjøre
- 1Clear the fault code and drive the car; check whether it returns
- 2Measure the cable from the control module to the left knock sensor: it should be unbroken, and with a multimeter it should have no contact with ground (the body)
- 3Check the earth wire and the connectors in the harness for contact resistance and oxidation
- 4If you have a diagnostic tool: read the knock signal in live data with the engine running and see whether the value is missing or stays at a constant low level
- 5Have a workshop with diagnostic equipment check and repair the wiring to the knock sensor
Symptomer du kan merke1
- Poor performance and lack of power while driving
Hva feilen kan påvirke2
- Ignition timing is retarded as a safety measure
- Boost pressure is reduced
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.