VOLVO
ECM-P032815 - Knock Sensor 1 Circuit High (Bank 1). General Electrical Failures. Circuit short to battery or open
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (20)
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Kun motor: B4204T6
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Kun motor: B4204T6
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
The engine control module (ECM) monitors the signal from the left knock sensor and sets the fault code when the signal is too high. This can be caused by a signal cable short-circuited to voltage or by an open circuit. An incorrectly fitted or damaged knock sensor can also produce the fault code.
Mulige årsaker
- Signal cable short-circuited to voltage
- Incorrectly fitted knock sensor
- Damaged knock sensor
Hva du kan gjøre
- 1Clear the fault code and test drive the car to see whether it returns
- 2Check that the wiring to the left knock sensor is complete, with no breaks or chafing, and that the plug is firmly connected
- 3With a multimeter, confirm that the cable is unbroken and has no contact with the positive supply
- 4Check that the left knock sensor is correctly fitted
- 5Have a workshop with diagnostic equipment check the sensor and the wiring and replace the knock sensor if needed
Symptomer du kan merke1
- Poor performance and lack of power while driving
Hva feilen kan påvirke2
- Ignition timing is retarded as a safety measure
- Boost pressure is reduced
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.