VOLVO
ECM-P033116 - Knock Sensor 2 Circuit Range/Performance (Bank 2). General Electrical Failures. Circuit voltage below threshold
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (20)
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Kun motor: B4204T6
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Kun motor: B4204T6
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
At some operating points the ECM watches the right knock sensor output. If that output is too low, the fault code is set. The causes may be a loose sensor, poor contact, a break in the signal cable, or signal cables that are short-circuited to each other.
Mulige årsaker
- Loose knock sensor
- Contact resistance in the knock sensor connections
- Break in the signal cable
- Short circuit between the knock sensors' signal cables
- Damaged knock sensor
Hva du kan gjøre
- 1Read the fault code, clear it and test drive the car
- 2Check that the right knock sensor is firmly seated
- 3Check the sensor connections for contact resistance and oxidation
- 4Check the signal cables for breaks; with a multimeter, confirm that they have no contact with each other
- 5Have a workshop with diagnostic equipment check and, if needed, replace the damaged knock sensor
Symptomer du kan merke1
- Poor performance and lack of power while driving
Hva feilen kan påvirke2
- Ignition timing is retarded as a safety measure
- Boost pressure is reduced
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.