VOLVO
ECM-P033211 - Knock Sensor 2 Circuit Low (Bank 2). General Electrical Failures. Circuit short to ground
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (20)
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Kun motor: B4204T6
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Kun motor: B4204T6
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
The signal from the right knock sensor is too low. The engine control module (ECM) compares the signal with limits and sets the fault code when it deviates. A signal cable that has been short-circuited to ground is one possible cause. Poor contact, a break or a damaged sensor can produce the same fault code.
Mulige årsaker
- Signal cable short-circuited to ground
- Contact resistance in the knock sensor connections
- Break in the signal cable
- Short circuit between the knock sensors' signal cables
- Damaged knock sensor
Hva du kan gjøre
- 1Read the fault code, clear it and test drive the car
- 2Check the signal cable from the right knock sensor for a short to ground; with a multimeter, confirm that the cable has no contact with the body
- 3Check the connections to the right knock sensor for contact resistance and oxidation
- 4If you have a diagnostic tool: read the knock signal from the right sensor in live data with the engine running and see whether it is too low
- 5Have a workshop with diagnostic equipment check the wiring and replace the knock sensor if needed
Symptomer du kan merke1
- Poor performance and lack of power while driving
Hva feilen kan påvirke2
- Ignition timing is retarded as a safety measure
- Boost pressure is reduced
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.