VOLVO
ECM-P033900 - Crankshaft Position Sensor A Circuit Intermittent. General Failure Information. No sub type information
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Feilkoden har ulik betydning avhengig av modell, årsmodell eller motor. Velg betydningen som gjelder din bil.
Gjelder følgende modeller:
13 modellerC30 (2007–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Vis modeller per årsmodell og motor (40)
- Volvo C30 (2007–2013)2011–2013Kun motor: D4162T
- Volvo S40 (2004–2013)2011–2012Kun motor: D4162T
- Volvo S60 (2011–)2011–2012Kun motor: B6304T4, D4162T
- Volvo S60 (2011–)2013–2014Kun motor: B5204T8, B5204T9, B5254T12, B5254T14, B6304T4, D4162T
- Volvo S60 (2011–)2015Kun motor: B5204T8, B5204T9, B5254T12, B5254T14, B6304T3, B6304T4, B6304T5, D4162T
- Volvo S80 (2007–)2007Kun motor: B6324S, B8444S
- Volvo S80 (2007–)2008–2009Kun motor: B6304T2, B6324S, B8444S
- Volvo S80 (2007–)2010Kun motor: B6304T2, B6324S, B6324S2, B8444S, D4164T
- Volvo S80 (2007–)2011Kun motor: B6304T4, B6324S4, B6324S5, B8444S, D4164T
- Volvo S80 (2007–)2012, 2015Kun motor: B6304T4, B6324S4, B6324S5, D4162T
- Volvo S80 (2007–)2013–2014Kun motor: B5254T12, B5254T14, B6304T4, B6324S4, B6324S5, D4162T
- Volvo V40 (2013–)2013Alle motorer unntatt: B4164T, B4164T3, D5204T4, D5204T6
- Volvo V40 (2013–)2014Kun motor: B5204T8, B5204T9, B5254T12, B5254T14, D4162T
- Volvo V40 (2013–)2015Kun motor: B5204T8, B5204T9, D4162T
- Volvo V40 Cross Country (2013–)2013–2014Alle motorer unntatt: B4164T, D5204T4, D5204T6
- Volvo V40 Cross Country (2013–)2015Alle motorer unntatt: B4164T, B4204T11, D4204T14, D5204T6
- Volvo V50 (2004–2013)2011–2012Kun motor: D4162T
- Volvo V60 (2011–)2011–2012Kun motor: B6304T4, D4162T
- Volvo V60 (2011–)2013Kun motor: B5204T8, B5204T9, B6304T4, D4162T
- Volvo V60 (2011–)2014Kun motor: B5204T8, B5204T9, B5254T12, B6304T4, D4162T
- Volvo V60 (2011–)2015Kun motor: B5204T9, B5254T12, B6304T3, B6304T4, B6304T5, D4162T
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008–2009Kun motor: B6304T2, B6324S
- Volvo V70 (2008–)2010Kun motor: B6304T2, B6324S, B6324S2, D4164T
- Volvo V70 (2008–)2011Kun motor: B6304T4, B6324S5, D4164T
- Volvo V70 (2008–)2012Kun motor: B6304T4, B6324S5, D4162T
- Volvo V70 (2008–)2013–2014Kun motor: B5204T9, B6304T4, B6324S5, D4162T
- Volvo V70 (2008–)2015Kun motor: B5204T9, B6304T4, D4162T
- Volvo XC60 (2009–)2009Kun motor: B6304T2
- Volvo XC60 (2009–)2010Kun motor: B6304T2, B6324S, B6324S2
- Volvo XC60 (2009–)2011–2014Kun motor: B6304T4, B6324S4, B6324S5
- Volvo XC60 (2009–)2015Kun motor: B5204T9, B5254T12, B5254T14, B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2008Kun motor: B6324S
- Volvo XC70 (2008–)2009Kun motor: B6304T2, B6324S
- Volvo XC70 (2008–)2010Kun motor: B6304T2, B6324S, B6324S2
- Volvo XC70 (2008–)2011–2015Kun motor: B6304T4, B6324S4, B6324S5
- Volvo XC90 (2003–)2005–2006Kun motor: B8444S
- Volvo XC90 (2003–)2007–2010Kun motor: B6324S, B8444S
- Volvo XC90 (2003–)2011Kun motor: B6324S5, B8444S
- Volvo XC90 (2003–)2012–2014Kun motor: B6324S5
Hva betyr feilkoden?
The fault is recorded as intermittent, meaning it comes and goes, and it may not be present right now. The engine control module counts the teeth on the flywheel, or the holes in the carrier plate, using the crankshaft position sensor signal. The fault is stored when the count is wrong over a set number of crankshaft revolutions.
Mulige årsaker
- Signal wires have an open circuit or are shorted to ground or supply voltage
- Loose connections
- Contact resistance or oxidation in the connections
- Sensor fitted incorrectly or damaged
- Damage to the flywheel or carrier plate
Hva du kan gjøre
- 1If you have a diagnostic tool, start the engine, raise the speed and read the fault status. 'Fault found' means a permanent fault.
- 2Check that the fuses are intact.
- 3Use a multimeter to check that the signal wires to the sensor have no open circuit and no short to ground or supply voltage.
- 4Check that the connector at the sensor is secure and free from oxidation and contact resistance.
- 5Check that the sensor is correctly fitted. If the fault returns, have a workshop check the flywheel and carrier plate for damage.
- 6If you have a diagnostic tool, follow the engine speed in live data while the engine runs and check that the value is steady.
Symptomer du kan merke2
- Engine stalls
- Engine does not start and only cranks
Hva feilen kan påvirke1
- The ECM may use the camshaft sensor signal instead
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.