VOLVO
ECM-P034400 - Camshaft Position Sensor A Circuit Intermittent (Bank 1 or single sensor). General Failure Information. No sub type information
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Feilkoden har ulik betydning avhengig av modell, årsmodell eller motor. Velg betydningen som gjelder din bil.
Gjelder følgende modeller:
10 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Vis modeller per årsmodell og motor (36)
- Volvo S60 (2011–)2011–2012Kun motor: B5254T5, B6304T4
- Volvo S60 (2011–)2013–2014Kun motor: B5204T8, B5204T9, B5254T12, B5254T14, B6304T4
- Volvo S60 (2011–)2015Kun motor: B5204T8, B5204T9, B5254T12, B5254T14, B6304T3, B6304T4, B6304T5
- Volvo S80 (2007–)2007Alle motorer unntatt: D5244T4, D5244T5
- Volvo S80 (2007–)2008Kun motor: B5254T6, B6304T2, B6324S, B8444S
- Volvo S80 (2007–)2009Kun motor: B5254T6, B5254T8, B6304T2, B6324S, B8444S
- Volvo S80 (2007–)2010Alle motorer unntatt: B4204S3, B4204S4, B4204T6, D4204T, D5244T10, D5244T14, D5244T19
- Volvo S80 (2007–)2011Alle motorer unntatt: B4164T, B4204S3, B4204S4, B4204T6, B4204T7, D5204T2, D5244T10
- Volvo S80 (2007–)2012Kun motor: B5254T10, B6304T4, B6324S4, B6324S5
- Volvo S80 (2007–)2013–2014Kun motor: B5254T12, B5254T14, B6304T4, B6324S4, B6324S5
- Volvo S80 (2007–)2015Kun motor: B6304T4, B6324S4, B6324S5
- Volvo V40 (2013–)2013–2014Kun motor: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V40 (2013–)2015Kun motor: B5204T8, B5204T9
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V60 (2011–)2011–2012Kun motor: B6304T4
- Volvo V60 (2011–)2013Kun motor: B5204T8, B5204T9, B6304T4
- Volvo V60 (2011–)2014Kun motor: B5204T8, B5204T9, B5254T12, B6304T4
- Volvo V60 (2011–)2015Kun motor: B5204T9, B5254T12, B6304T3, B6304T4, B6304T5
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008Kun motor: B5254T6, B6304T2, B6324S
- Volvo V70 (2008–)2009Kun motor: B5254T6, B5254T8, B6304T2, B6324S
- Volvo V70 (2008–)2010Kun motor: B5254T10, B5254T11, B6304T2, B6324S, B6324S2, D4164T
- Volvo V70 (2008–)2011Kun motor: B5254T10, B5254T11, B6304T4, B6324S5, D4164T
- Volvo V70 (2008–)2012Kun motor: B5254T10, B6304T4, B6324S5
- Volvo V70 (2008–)2013–2014Kun motor: B5204T9, B6304T4, B6324S5
- Volvo V70 (2008–)2015Kun motor: B5204T9, B6304T4
- Volvo XC60 (2009–)2009Kun motor: B6304T2
- Volvo XC60 (2009–)2010Kun motor: B6304T2, B6324S, B6324S2
- Volvo XC60 (2009–)2011–2014Kun motor: B6304T4, B6324S4, B6324S5
- Volvo XC60 (2009–)2015Kun motor: B5204T9, B5254T12, B5254T14, B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2008Kun motor: B6324S
- Volvo XC70 (2008–)2009Kun motor: B6304T2, B6324S
- Volvo XC70 (2008–)2010Kun motor: B6304T2, B6324S, B6324S2
- Volvo XC70 (2008–)2011–2015Kun motor: B6304T4, B6324S4, B6324S5
- Volvo XC90 (2003–)2007–2010Kun motor: B6324S
- Volvo XC90 (2003–)2011–2014Kun motor: B6324S5
Hva betyr feilkoden?
The fault is recorded as intermittent, meaning it comes and goes, and it may not be present right now. The engine control module (ECM) reads the PWM signal from the camshaft sensor. The fault is stored when the signal is missing from time to time, or when the camshaft has too few segments over a set number of crankshaft revolutions. The code applies to the intake camshaft sensor on bank 1.
Mulige årsaker
- Camshaft sensor in the wrong position
- Damaged camshaft sensor
- Loose connections
- Contact resistance and oxidation in the connections
- Open circuit or short circuit to ground or supply voltage in the signal wire
- Camshaft sensor fitted incorrectly
Hva du kan gjøre
- 1If you have a diagnostic tool, start the engine, raise the speed and read the fault status. 'Fault found' means the fault is permanent.
- 2Check that the fuses are intact.
- 3With the ignition off, check that the connector at the camshaft sensor is clean, secure and free from contact resistance and oxidation.
- 4Check that the camshaft sensor is correctly fitted and that the housing around it is not damaged, since that can affect its position.
- 5If your diagnostic tool shows it, read the camshaft sensor position or speed in live data while the engine runs.
- 6If the fault returns, have a workshop check the camshaft sensor and its signal wire.
Symptomer du kan merke5
- Engine is hard to start
- Check engine light (emissions warning lamp) is on
- Automatic engine start/stop does not work
- Car lacks power
- Car hesitates or jerks while driving
Hva feilen kan påvirke3
- The ECM uses the crankshaft sensor signal instead
- Variable valve timing (VVT) control is blocked
- Camshaft control is switched off
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.