VOLVO
ECM-P062F46 - Internal Control Module EEPROM Error. System Internal Failures. Calibration / parameter memory failure
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (20)
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Kun motor: B4204T6
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Kun motor: B4204T6
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
The engine control module (ECM) monitors its own memory where the calibration and parameter values are stored (EEPROM). The code is set when the module finds an internal fault in that memory. The check starts when the ignition is switched on, and the fault can only be found while the test is running and the conditions are met. The timing of the symptoms is unclear, and the engine may stall or fail to start.
Mulige årsaker
- Communication interference
- Damaged engine control module (ECM)
Hva du kan gjøre
- 1Switch on the ignition and wait a short while before reading the codes, so the module can complete its test
- 2Read the fault code status and check that the fault is no longer active when the test is complete
- 3Check whether other fault codes are stored in the engine control module; these should be traced first
- 4If the code returns after it has been cleared and the car has been road tested, the engine control module needs replacing; have a workshop do this
Symptomer du kan merke2
- The engine may stall while driving, at an unclear moment or all the time
- The engine does not start
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.