VOLVO
ECM-P080582 - Clutch Position Sensor "A" Circuit. Bus Signal / Message Failures. Alive / sequence counter incorrect / not updated
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (20)
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Kun motor: B4204T6
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Kun motor: B4204T6
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
The clutch position sensor signal is sent from the central electronic module (CEM) to the engine control module over the CAN bus, and the ECM compares it with the position switch that is wired directly to it. The code is set when the position sensor signal is faulty, for example when the counter that accompanies the message is wrong or is not updated.
Mulige årsaker
- Position switch incorrectly installed, adjusted or sticking
- Contact resistance, oxidation or loose connection in the connector
- Faulty position switch
Hva du kan gjøre
- 1Read the engine control module fault codes. If any of ECM-U012088, ECM-U000188, ECM-U1A1400, ECM-U000108 or ECM-U000100 is stored, investigate it first, as it is most likely the cause of this code
- 2Read the CEM fault codes. If the CEM has stored its own fault, that is most likely the root cause and this code is a knock-on fault
- 3Check that the fuses are intact. The locations are shown in the instruction manual or on the fuse list
- 4Check that the connectors at the position switch are firmly seated, dry and free from oxidation
- 5Check that the clutch pedal and position switch move freely and do not stick, and that the switch is correctly fitted and adjusted
- 6If you have a diagnostic tool, read the clutch pedal position in live data and check that the value follows the pedal movement smoothly as it is pressed down and released
Symptomer du kan merke1
- No noticeable symptoms for the driver
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.