VOLVO
ECM-P12631E - Cylinder #3 High To Low Side Short. General Electrical Failures. Circuit resistance out of range
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (20)
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Kun motor: B4204T6
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Kun motor: B4204T6
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
Although the code is named as a high to low side short, it applies to the current signal to the cylinder 3 injector, which is too low compared with the request. The engine control module detects the fault while the engine is running. The cause can be contact resistance or oxidation in the connections, or a damaged engine control module.
Mulige årsaker
- Contact resistance or oxidation in the connections
- Damaged engine control module (ECM)
Hva du kan gjøre
- 1Check that the fuses are intact. The locations are in the owner's manual or on the fuse box cover.
- 2Look at the connector to the cylinder 3 injector: it should be secure and free from oxide and corrosion.
- 3Have a workshop measure the internal resistance of the injector so that a damaged injector can be ruled out.
- 4If the injector and its connectors are fine, the engine control module may be at fault, and a workshop would then replace it.
- 5When the work is done, read the code again with the engine running to confirm it has cleared.
Symptomer du kan merke3
- The Check engine (malfunction) lamp comes on or behaves abnormally
- The engine does not start
- The engine is hard to start and cranks slowly
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.