VOLVO
ECM-P12641E - Cylinder #4 High To Low Side Short. General Electrical Failures. Circuit resistance out of range
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (20)
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Kun motor: B4204T6
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Kun motor: B4204T6
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
Even though the code is named as a short between the high and low side, it applies to the current signal to the cylinder 4 injector, which is too low compared with what is requested. The engine control module detects the fault while the engine is running. The cause can be contact resistance or oxidation in the connections, or a damaged engine control module.
Mulige årsaker
- Contact resistance or oxidation in the connections to the injector
- Damaged engine control module (ECM)
Hva du kan gjøre
- 1Check that the connector to the cylinder 4 injector is secure and free from oxide and corrosion.
- 2Check that the fuses are intact. The locations are in the owner's manual or on the fuse box cover.
- 3Have a workshop measure the internal resistance of the injector with diagnostic equipment, to rule out a damaged injector.
- 4If the injector and connectors are in order, the engine control module is what may be at fault, and a workshop replaces it.
- 5When the work is finished, read the code again with the engine running so you can see that it has gone.
Symptomer du kan merke3
- The Check engine (malfunction) lamp comes on or behaves abnormally
- The engine does not start
- The engine is hard to start and cranks slowly
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.