VOLVO
ECM-P193484 - Vehicle Speed Signal. Bus Signal / Message Failures. Signal below allowable range
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (20)
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Kun motor: B4204T6
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Kun motor: B4204T6
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
Although the code is named signal below allowable range, it applies when the engine control module (ECM) has registered that the speed value reported by the brake control module (BCM) is excessively high. The code is event controlled: it does not show a fault in the control module where it is active, but works mainly as information. It is only set when driving under certain conditions and disappears when those conditions no longer apply.
Mulige årsaker
- Faulty speed value from the brake control module (BCM), where the cause should be looked for
Hva du kan gjøre
- 1Read off the codes in the brake control module (BCM) first and remedy them
- 2Investigate the speed signal while driving, as the code is only set under certain driving conditions
- 3If the code remains after the fault in the brake control module has been remedied, it can be cleared in the engine control module
- 4Check the connectors to the brake control module and its wiring for chafing and moisture
Symptomer du kan merke1
- No noticeable symptoms for the driver
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.