VOLVO
ECM-P193485 - Vehicle Speed Signal. Bus Signal / Message Failures. Signal above allowable range
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (20)
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Kun motor: B4204T6
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Kun motor: B4204T6
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
Although the code is named signal above allowable range, it applies when the speed value from the brake control module (BCM) does not change as it should for too long. The engine control module (ECM) monitors the signal and sets the code when it stays unchanged. The fault can only be detected when driving under certain conditions, and the code is stored in the BCM first and then in the ECM.
Mulige årsaker
- Fault in the speed value from the brake control module (BCM), where the cause should be looked for
Hva du kan gjøre
- 1Read off the codes in the brake control module (BCM) first and remedy them
- 2Clear the code in the engine control module only once the code in the brake control module has been cleared and the fault remedied
- 3Check the connectors and wiring to the brake control module for play, corrosion and damage
- 4If you have a diagnostic tool: check in live data that the speed value from the brake control module changes when the car is moving
- 5Test drive the car after the repair, as the fault is only tested when driving under certain conditions
Symptomer du kan merke1
- Check engine warning lamp lights or behaves abnormally
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.