VOLVO
ECM-P223800 - O2 Sensor Positive Current Control Circuit Low - Bank 1, Sensor 1. General Failure Information. No sub type information
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
12 modellerC30 (2007–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Vis modeller per årsmodell og motor (22)
- Volvo C30 (2007–2013)2011–2013Kun motor: D4162T
- Volvo S40 (2004–2013)2011–2012Kun motor: D4162T
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, B5254T5, D4162T
- Volvo S60 (2011–)2012Kun motor: B4164T, B4164T2, B4164T3, B5254T5, D4162T
- Volvo S60 (2011–)2013–2015Kun motor: B4164T, B4164T2, B4164T3, D4162T
- Volvo S80 (2007–)2007–2009Kun motor: D5244T4, D5244T5
- Volvo S80 (2007–)2011Kun motor: B4164T
- Volvo S80 (2007–)2012–2014Kun motor: B4164T, B4164T2, D4162T
- Volvo S80 (2007–)2015Kun motor: B4164T, D4162T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3, D4162T
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4, D4162T
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T, D4162T
- Volvo V50 (2004–2013)2011–2012Kun motor: D4162T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, D4162T
- Volvo V60 (2011–)2012–2015Kun motor: B4164T, B4164T2, B4164T3, D4162T
- Volvo V70 (2008–)2008–2009Kun motor: D5244T4, D5244T5
- Volvo V70 (2008–)2011Kun motor: B4164T
- Volvo V70 (2008–)2012–2015Kun motor: B4164T, B4164T2, D4162T
- Volvo XC60 (2009–)2009Alle motorer unntatt: B6304T2
- Volvo XC70 (2008–)2008Alle motorer unntatt: B6324S
- Volvo XC70 (2008–)2009Kun motor: D5244T4, D5244T5
- Volvo XC90 (2003–)2013–2014Kun motor: D5244T18, D5244T5
Hva betyr feilkoden?
The module reads the front heated oxygen sensor, which reports on the fuel and air mixture. The code is set when the signal from the sensor is faulty, here too low. The fault can also lie in the pump current wire if the pump current has stopped.
Mulige årsaker
- Short to earth on the signal wire
- Open circuit in the signal wire
- Contact resistance or oxidation in the connections
- Open circuit in the pump current wire
- Damaged front heated oxygen sensor (HO2S)
- Codes ECM-P223700 or ECM-P223900 stored at the same time
Hva du kan gjøre
- 1Check that the fuses are intact
- 2Check the oxygen sensor connections for contact resistance, looseness and oxidation. Do not use rust-dissolving spray or grease in the connector
- 3Use a multimeter to check that the signal wire has no short to earth
- 4If the wiring is in order, try a new oxygen sensor
- 5If the fault remains, have a workshop with diagnostic equipment diagnose further
Symptomer du kan merke1
- Malfunction indicator lamp (MIL) lit
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.