VOLVO
ECM-P230412 - Ignition Coil B Primary Control Circuit High. General Electrical Failures. Circuit short to battery
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (20)
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Kun motor: B4204T6
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Kun motor: B4204T6
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
The engine control module (ECM) monitors the signal line to the ignition coil primary winding. The code is set when the signal is too high, which in this case means the signal line to ignition coil 2 has been short-circuited to supply voltage. It is an electrical fault in the circuit, and the code applies only to this ignition coil.
Mulige årsaker
- The signal wire to ignition coil 2 is short-circuited to supply voltage
- The ignition coil is damaged
Hva du kan gjøre
- 1Check that the relevant fuses are intact; their locations are shown in the car's owner's manual
- 2Read and note the code, clear it and run the engine for a while to see whether it returns
- 3Inspect the connector and cable at ignition coil 2 for loose contacts, corrosion, chafing and pinching
- 4Use a multimeter to check that the signal wire to ignition coil 2 has no contact with supply voltage
- 5If the fault returns, have a workshop with diagnostic equipment check the ignition coil and its wiring
Symptomer du kan merke2
- The engine warning lamp (Check engine) lights up or behaves abnormally
- The car runs poorly and lacks power
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.