VOLVO
ECM-P231012 - Ignition Coil D Primary Control Circuit High. General Electrical Failures. Circuit short to battery
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (20)
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Kun motor: B4204T6
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Kun motor: B4204T6
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
The engine control module (ECM) monitors the signal to ignition coil 4 and sets the code when it is too high. This is a short circuit to supply voltage, meaning the signal wire has come into contact with battery voltage. The fault is electrical and applies only to ignition coil 4.
Mulige årsaker
- The signal wire to ignition coil 4 is short-circuited to supply voltage
- The ignition coil is damaged
Hva du kan gjøre
- 1The fuses should be intact; their locations are shown in the car's owner's manual
- 2Read and note the code, clear it and drive to see whether it returns
- 3Inspect the wiring to ignition coil 4 for chafing, pinching and loose contacts
- 4Use a multimeter to check that the wire to ignition coil 4 has no contact with supply voltage
- 5If the fault returns, have a workshop with diagnostic equipment check the ignition coil and the wiring
Symptomer du kan merke2
- The engine warning lamp (Check engine) lights up or behaves abnormally
- The car runs poorly and lacks power
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.