VOLVO
ECM-P250A13 - Engine Oil Level Sensor Circuit. General Electrical Failures. Circuit open
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
8 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–), XC70 (2008–)
Vis modeller per årsmodell og motor (17)
- Volvo S60 (2011–)2011–2012Kun motor: B5254T5
- Volvo S60 (2011–)2014–2015Kun motor: B4204T10, B4204T11, B4204T12, B4204T15, B4204T9, D4204T5
- Volvo S80 (2007–)2007–2008Kun motor: B5254T6
- Volvo S80 (2007–)2009Kun motor: B5254T6, B5254T8
- Volvo S80 (2007–)2010–2011Kun motor: B5254T10, B5254T11, B5254T8
- Volvo S80 (2007–)2012Kun motor: B5254T10
- Volvo S80 (2007–)2014–2015Kun motor: B4204T11, B4204T12, B4204T15, D4204T5
- Volvo V40 (2013–)2015Kun motor: B4204T11, D4204T14
- Volvo V40 Cross Country (2013–)2015Kun motor: B4204T11, D4204T14
- Volvo V60 (2011–)2014–2015Kun motor: B4204T11, B4204T12, B4204T15, B4204T9, D4204T5
- Volvo V70 (2008–)2008Kun motor: B5254T6
- Volvo V70 (2008–)2009Kun motor: B5254T6, B5254T8
- Volvo V70 (2008–)2010–2011Kun motor: B5254T10, B5254T11
- Volvo V70 (2008–)2012Kun motor: B5254T10
- Volvo V70 (2008–)2014–2015Kun motor: B4204T11, D4204T5
- Volvo XC60 (2009–)2014–2015Kun motor: B4204T10, B4204T11, B4204T12, B4204T15, B4204T9, D4204T5
- Volvo XC70 (2008–)2014–2015Kun motor: B4204T11, D4204T5
Hva betyr feilkoden?
The ECM reads the signal from the oil level sensor and uses it to monitor the oil level. The code is stored when that signal is incorrect, which may be an electrical fault in the sensor or its wiring. Water or fuel in the engine oil can also trigger it.
Mulige årsaker
- Contact resistance, oxidation or loose contact in the connections
- Open circuit in the signal wire
- Open circuit in the power supply
- Water or fuel in the engine oil
- Damaged oil level sensor
Hva du kan gjøre
- 1Read the fault status with the engine running. If the code is not active, the fault may have been intermittent
- 2Check that the relevant fuses are intact
- 3Check whether water or fuel may have got into the engine oil. If so, the code can be set, and the remedy is to run the engine fully warm
- 4Use a multimeter to check that the power supply and signal wire to the oil level sensor have no open circuit
- 5If the fault remains after these checks, have a workshop with diagnostic equipment check the oil level sensor
Symptomer du kan merke1
- The oil pressure warning lamp comes on or behaves abnormally
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.