VOLVO
ECM-U010183 - Lost communication with Transmission Control Module (TCM). Bus Signal / Message Failures. Value of signal protection calculation incorrect
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (20)
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Kun motor: B4204T6
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Kun motor: B4204T6
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
The ECM gets speed data for the car from the transmission control module (TCM) over CAN. The code is set when the checksum in the message from the TCM is wrong, which may be caused by a damaged TCM or by interference on the CAN network.
Mulige årsaker
- Damaged transmission control module (TCM)
- Interference on the CAN network
Hva du kan gjøre
- 1Read the code with a diagnostic tool and see whether it is active or only stored
- 2Start with the codes in the transmission control module (TCM), since it sends the speed information
- 3If you have a diagnostic tool: compare the vehicle speed in live data with the speedometer during a test drive
- 4Have a workshop check the CAN network for interference, since the fault can come from the network and not only from the transmission control module
Symptomer du kan merke1
- Check engine light comes on or behaves abnormally
Hva feilen kan påvirke1
- The ECM uses the BCM's speed value instead, as long as that value is valid
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.